Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations

The paper reports the research on the improvement of tool wear resistant of Titanium Carbide (TiC) cutting tool after microwave post sintering treatment. Titanium Carbide square milling insert was microwave sintered at 600°C with 15 minutes of holding time. The face milling operations were conducted...

Full description

Bibliographic Details
Main Authors:	Iqbal, Mohammad, Ariff, Tasnim Firdaus, Fahmi, Shahrul, Al Hazza, Muataz Hazza Faizi, Hilmy, Irfan, Suryanto, -
Format:	Conference or Workshop Item
Language:	English English
Published:	2014
Subjects:	T Technology (General)
Online Access:	http://irep.iium.edu.my/39806/ http://irep.iium.edu.my/39806/ http://irep.iium.edu.my/39806/1/ICAMME2014-ID-2132.pdf http://irep.iium.edu.my/39806/2/ICAMME_2014_Program.pdf

id	iium-39806
recordtype	eprints
spelling	iium-398062015-01-09T03:04:49Z http://irep.iium.edu.my/39806/ Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations Iqbal, Mohammad Ariff, Tasnim Firdaus Fahmi, Shahrul Al Hazza, Muataz Hazza Faizi Hilmy, Irfan Suryanto, - T Technology (General) The paper reports the research on the improvement of tool wear resistant of Titanium Carbide (TiC) cutting tool after microwave post sintering treatment. Titanium Carbide square milling insert was microwave sintered at 600°C with 15 minutes of holding time. The face milling operations were conducted to Carbon Steel S45C block (130 mm x 95 mm x 40 mm) by using both of original and microwave sintered insert at 5 different cutting speed (60, 90 , 120 , 150 and 180 m/min), constant feed rate (0.2 mm/tooth) and constant depth of cut(0.2 mm/tooth). The flank wear of the insert was measured every nearest 10th minute of complete cutting passes. The results of the experiment show that microwave post sintering treatment improves the tool resistant of the TiC insert. The flank wear of the sintered insert is lower at any machining time and all cutting speed. The research also found that the percentage of the improvement is lower at higher cutting speed compare to lower cutting speed. 2014 Conference or Workshop Item PeerReviewed application/pdf en http://irep.iium.edu.my/39806/1/ICAMME2014-ID-2132.pdf application/pdf en http://irep.iium.edu.my/39806/2/ICAMME_2014_Program.pdf Iqbal, Mohammad and Ariff, Tasnim Firdaus and Fahmi, Shahrul and Al Hazza, Muataz Hazza Faizi and Hilmy, Irfan and Suryanto, - (2014) Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations. In: IIUM Engineering Congress : 3rd International Conference on Mathematical Application in Engineering 2014, 23rd - 25th September 2014, Kuala Lumpur. https://sites.google.com/site/icamme14/
repository_type	Digital Repository
institution_category	Local University
institution	International Islamic University Malaysia
building	IIUM Repository
collection	Online Access
language	English English
topic	T Technology (General)
spellingShingle	T Technology (General) Iqbal, Mohammad Ariff, Tasnim Firdaus Fahmi, Shahrul Al Hazza, Muataz Hazza Faizi Hilmy, Irfan Suryanto, - Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations
description	The paper reports the research on the improvement of tool wear resistant of Titanium Carbide (TiC) cutting tool after microwave post sintering treatment. Titanium Carbide square milling insert was microwave sintered at 600°C with 15 minutes of holding time. The face milling operations were conducted to Carbon Steel S45C block (130 mm x 95 mm x 40 mm) by using both of original and microwave sintered insert at 5 different cutting speed (60, 90 , 120 , 150 and 180 m/min), constant feed rate (0.2 mm/tooth) and constant depth of cut(0.2 mm/tooth). The flank wear of the insert was measured every nearest 10th minute of complete cutting passes. The results of the experiment show that microwave post sintering treatment improves the tool resistant of the TiC insert. The flank wear of the sintered insert is lower at any machining time and all cutting speed. The research also found that the percentage of the improvement is lower at higher cutting speed compare to lower cutting speed.
format	Conference or Workshop Item
author	Iqbal, Mohammad Ariff, Tasnim Firdaus Fahmi, Shahrul Al Hazza, Muataz Hazza Faizi Hilmy, Irfan Suryanto, -
author_facet	Iqbal, Mohammad Ariff, Tasnim Firdaus Fahmi, Shahrul Al Hazza, Muataz Hazza Faizi Hilmy, Irfan Suryanto, -
author_sort	Iqbal, Mohammad
title	Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations
title_short	Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations
title_full	Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations
title_fullStr	Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations
title_full_unstemmed	Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations
title_sort	effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations
publishDate	2014
url	http://irep.iium.edu.my/39806/ http://irep.iium.edu.my/39806/ http://irep.iium.edu.my/39806/1/ICAMME2014-ID-2132.pdf http://irep.iium.edu.my/39806/2/ICAMME_2014_Program.pdf
first_indexed	2023-09-18T20:57:09Z
last_indexed	2023-09-18T20:57:09Z
_version_	1777410379971821568

Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations

Similar Items