Abu a-Qasim al-Zahrawi's contribution to neurosurgery

by Mohamad Asharaf, Asfana Banu, Shuriye, Abdi Omar
Published 2011

Investigation of minimum chip thickness in micro end milling of PMMA: process development

by Mohammad , Yeakub Ali, -, Asfana Banu, -, Adibah, -, Nur Atikah
Published 2011

Investigation of recast layer of non-conductive ceramic due to micro-EDM

by Mohamed, Abd. Rahman, Asfana, Banu, Ali, Mohammad Yeakub
Published 2014

Micro electro discharge machining of non-conductive ceramic using conductive powder mix dielectric fluid

by Ali, Mohammad Yeakub, Suieb, Ali Nurhanim, Mohamad Asharaf, Asfana Banu
Published 2016

Influence of energy parameters of micro WEDM on kerf

by Ali, Mohammad Yeakub, Willey, Liew Yun Hsien, Gure, S. A., Asfana, Banu
Published 2012

Application of focused ion beam micromachining: a review

by Rahman Azmil, Nur Atiqah, Jaafar, Israd Hakim, Ali, Mohammad Yeakub, Asfana, Banu
Published 2012

Material removal rate of zirconia in electro discharge micromachining

by Asfana, Banu, Ali, Mohammad Yeakub, Mohamed, Abd. Rahman, Wayne, N. P. Hung
Published 2015

Critical chain in project management

by Adesta, Erry Yulian Triblas, Mohamad Ashraf, Asfana Banu, Abdul Rahman Azmil, Nur Atiqah
Published 2011

Investigation of vibration and surface roughness in micro milling of PMMA

by Ali, Mohammad Yeakub, Mohamed, Abd. Rahman, Asfana, Banu, Roslan, Lutfi, Fahmi, M. I.
Published 2012

Finish cut of titanium alloy using micro electro discharge milling for nano surface finish

by Mohammad , Yeakub Ali, -, Muhamad Faizal, Mohamad Asharaf, Asfana Banu, Abdul Rahman, Nur Atiqah
Published 2011

Investigation of TWR for finish cut of titanium alloy using Micro Electro Discharge Milling

by Mohammad , Yeakub Ali, -, Mohd Saifuddin, Abdul Rahman, Nur Atiqah, Mohamad Asharaf, Asfana Banu
Published 2011

Investigation of MRR for finish cut of titanium alloy using micro electro discharge milling

by Mohammad , Yeakub Ali, -, Mohd Saifuddin, Abdul Rahman, Nur Atiqah, Mohamad Asharaf, Asfana Banu
Published 2011

Prediction of minimum chip thickness in tool based micro end milling

by Ali, Mohammad Yeakub, Khan, Ahsan Ali, Mohamad Asharaf, Asfana Banu, Abdul Wahab, Adibah
Published 2012

Investigation of minimum chip thickness in micro end milling of PMMA: Experiment and analysis 800 µm diameter tool

by Mohammad , Yeakub Ali, Mohamad Ashraf, Asfana Banu, Abdul Wahab, Adibah, Abdul Rahman, Nur Atiqah
Published 2011

Investigation of minimum chip thickness in micro end milling of PMMA: experiment and analysis 1.0 mm diameter tool

by Mohammad , Yeakub Ali, Mohamad Ashraf, Asfana Banu, Abdul Wahab, Adibah, Abdul Rahman, Nur Atiqah
Published 2011

Empirical modelling of vibration in micro end milling of PMMA

by Ali, Mohammad Yeakub, Mohamed, Abd. Rahman, Khan, Ahsan Ali, Asfana, Banu, Lutfi, M., Fahmi, M. I.
Published 2013