Suggested Topics within your search.
Showing 1 - 20 results of 40 for search '"The Rakes"', query time: 0.05s Refine Results
  1. 1
    Tool life in high speed turning with negative rake angle
    “… at high speed cutting (1000mm/min) by using negative rake angle (90 to 12). The influence of increasing…”
    Get full text
    Get full text
    Get full text
    Get full text
  2. 2
    Tool life in high speed turning with negative rake angle
    Get full text
    Get full text
    Get full text
    Get full text
    Get full text
  3. 3
    Performance of cermet tools : applying negative rake angles high speed machining
    “… applying negative rake angles during high speed machining. In addition to that, cutting temperature is also…”
    Get full text
    Get full text
    Get full text
  4. 4
    Simulation of tool life for ceramic with negative rake angle using neural network
    “… of cutting speed, feed rate, depth of cut and rake angle. The model was built by using the neural network. A…”
    Get full text
    Get full text
    Get full text
    Get full text
  5. 5
    The economic impact of using negative rake angle in high speed hard turning
    “… negative rake angle, the cutting forces will shift from the edge of the cutting tool to the flank face…”
    Get full text
    Get full text
  6. 6
    Effect of rake angle and feed rate on chip segmentation in machining carbon steel 1050
    by Mohd Fawzi, Zamri, A. R., Yusoff
    Published 2018
    “… speed, feed rate, depth of cut and rake angle. In this study, experiments were carried out on carbon…”
    Get full text
    Get full text
    Get full text
  7. 7
    Management science an introduction
    by Davis
    Published 1986
  8. 8
    Experimental Investigation of the Effect of Feed Rate and Negative Tool Rake Angle in High Speed Hard Turning
    “…The aim of this paper is to study experimentally the influence of feed rate and negative tool rake…”
    Get full text
    Get full text
    Get full text
  9. 9
    High precision estimation on physical behavior for cutting with various tool rake angle by finite element method
    Get full text
    Get full text
    Get full text
    Get full text
    Get full text
  10. 10
    Cutting force impact to tool life of CT5015 in high speed machining by applying negative rake angles
    “… rake angles in high speed machining process. Experiments were carried out by using cermet insert (CT…”
    Get full text
    Get full text
    Get full text
  11. 11
    Tool wear and surface finish investigation in high speed turning using cermet insert by applying negative rake angles
    “… different rake angles and different cutting speed. Experiments were carried out by using cermet (CT5015…”
    Get full text
    Get full text
    Get full text
  12. 12
    Gender differences in reading comprehension via multimedia visual presentations / Syarifah Nurulaini Syed Abdul Mutalib
    “…), numerous researches had supported the evidence that using visuals in teaching could enhance learning (Rakes…”
    Get full text
    Get full text
  13. 13
    Health tourism in Malaysia: the strength and weaknesses
    “…. For participating countries, this new industry rakes in billions of dollars a year, and is worth focusing…”
    Get full text
    Get full text
    Get full text
  14. 14
    High speed end milling of single crystal silicon using diamond coated tools
    “… of rake angle which will obtain ductile mode machining. Thimmaiah et al. [1] also did machining…”
    Get full text
    Get full text
    Get full text
  15. 15
    Influence of cutting tool angles on the formation of built-up-edge
    “… of built-up-edge (BUE). Side cutting and rake angles of the cutting tool were chosen for the study…”
    Get full text
    Get full text
  16. 16
    Flank Wear Modeling in High Speed Hard Turning by using artificial Neural Network and Regression Analysis
    “… with negative rake angle was conducted using two different techniques. Regression model is developed by using…”
    Get full text
    Get full text
    Get full text
    Get full text
  17. 17
    Energy cost optimization in high speed hard turning using simulated annealing algorithm
    “… and negative rake angle using mixed ceramic as a cutting tool. Regression models have been developed by using…”
    Get full text
    Get full text
    Get full text
    Get full text
  18. 18
    Tool life modeling in high speed turning of AISI 4340 hardened steel with mixed ceramic tools by using face central cubic design
    “…) with three input factors: cutting speed, feed rate and negative rake angle. The Face Central Cubic Design…”
    Get full text
    Get full text
    Get full text
  19. 19
    Back Chip Temperature in Environmentally Conscious Turning with Conventional and Internally Cooled Cutting Tools
    “… removed from the blank. Chip-insert interaction occurs when the chip slides on the rake face of the insert…”
    Get full text
    Get full text
    Get full text
    Get full text
  20. 20
    Power Consumption Optimization in CNC Turning Process Using Multi Objective Genetic Algorithm
    “… are cutting speed, feed rate, depth of cut and rake angle. Due to complexity of this machining optimization…”
    Get full text
    Get full text
Search Tools: RSS Feed – Email Search