Investigation of mig welding on dissimilar thickness of metal sheets (steel and stainless steel)

Based on different welding parameters, a welding process between mild steel and stainless steel were performed in this experiment using metal inert gas (MIG) machine. The objective of this experiment was to investigate the effect of welding voltages (15V, 20V and 25V) wire feed rates (80 ipm and 100...

Full description

Bibliographic Details
Main Author:	Mohd Iqbal, Abd Razak
Format:	Undergraduates Project Papers
Language:	English
Published:	2012
Subjects:	TA Engineering (General). Civil engineering (General)
Online Access:	http://umpir.ump.edu.my/id/eprint/4658/ http://umpir.ump.edu.my/id/eprint/4658/ http://umpir.ump.edu.my/id/eprint/4658/1/cd6635_80.pdf

id	ump-4658
recordtype	eprints
spelling	ump-46582015-03-03T09:20:19Z http://umpir.ump.edu.my/id/eprint/4658/ Investigation of mig welding on dissimilar thickness of metal sheets (steel and stainless steel) Mohd Iqbal, Abd Razak TA Engineering (General). Civil engineering (General) Based on different welding parameters, a welding process between mild steel and stainless steel were performed in this experiment using metal inert gas (MIG) machine. The objective of this experiment was to investigate the effect of welding voltages (15V, 20V and 25V) wire feed rates (80 ipm and 100ipm) and filler metals (ER70S-6 and ER308L) to the microstructure and mechanical properties of the welded mild steel to stainless steel specimens. The microstructure changes and the mechanical properties result from tensile and hardness test were analyzed and compared between the welded zones, heat affected zone (HAZ) and base metal. From the results obtained the grain size of weld zone and HAZ increases when the welding voltage and wire feed rate increases. The strength of the welded joint was directly proportional to the increasing in voltage and wire feed rate but their hardness value was irreversibly proportional towards the increasing parameter value. Filler metal of ER70S-6 shows better result in hardness test while filler metal of ER308L shows better strength in the joint. In conclusion, increasing voltage and wire feed rate will increases the strength but lowered the hardness of the joint. Filler ER308L was suitable to be used to increase strength of the joint while filler ER70S-6 was more suitable in increasing the hardness of the joint. 2012-06 Undergraduates Project Papers NonPeerReviewed application/pdf en http://umpir.ump.edu.my/id/eprint/4658/1/cd6635_80.pdf Mohd Iqbal, Abd Razak (2012) Investigation of mig welding on dissimilar thickness of metal sheets (steel and stainless steel). Faculty of Mechanical Engineering, Universiti Malaysia Pahang. http://iportal.ump.edu.my/lib/item?id=chamo:68758&theme=UMP2
repository_type	Digital Repository
institution_category	Local University
institution	Universiti Malaysia Pahang
building	UMP Institutional Repository
collection	Online Access
language	English
topic	TA Engineering (General). Civil engineering (General)
spellingShingle	TA Engineering (General). Civil engineering (General) Mohd Iqbal, Abd Razak Investigation of mig welding on dissimilar thickness of metal sheets (steel and stainless steel)
description	Based on different welding parameters, a welding process between mild steel and stainless steel were performed in this experiment using metal inert gas (MIG) machine. The objective of this experiment was to investigate the effect of welding voltages (15V, 20V and 25V) wire feed rates (80 ipm and 100ipm) and filler metals (ER70S-6 and ER308L) to the microstructure and mechanical properties of the welded mild steel to stainless steel specimens. The microstructure changes and the mechanical properties result from tensile and hardness test were analyzed and compared between the welded zones, heat affected zone (HAZ) and base metal. From the results obtained the grain size of weld zone and HAZ increases when the welding voltage and wire feed rate increases. The strength of the welded joint was directly proportional to the increasing in voltage and wire feed rate but their hardness value was irreversibly proportional towards the increasing parameter value. Filler metal of ER70S-6 shows better result in hardness test while filler metal of ER308L shows better strength in the joint. In conclusion, increasing voltage and wire feed rate will increases the strength but lowered the hardness of the joint. Filler ER308L was suitable to be used to increase strength of the joint while filler ER70S-6 was more suitable in increasing the hardness of the joint.
format	Undergraduates Project Papers
author	Mohd Iqbal, Abd Razak
author_facet	Mohd Iqbal, Abd Razak
author_sort	Mohd Iqbal, Abd Razak
title	Investigation of mig welding on dissimilar thickness of metal sheets (steel and stainless steel)
title_short	Investigation of mig welding on dissimilar thickness of metal sheets (steel and stainless steel)
title_full	Investigation of mig welding on dissimilar thickness of metal sheets (steel and stainless steel)
title_fullStr	Investigation of mig welding on dissimilar thickness of metal sheets (steel and stainless steel)
title_full_unstemmed	Investigation of mig welding on dissimilar thickness of metal sheets (steel and stainless steel)
title_sort	investigation of mig welding on dissimilar thickness of metal sheets (steel and stainless steel)
publishDate	2012
url	http://umpir.ump.edu.my/id/eprint/4658/ http://umpir.ump.edu.my/id/eprint/4658/ http://umpir.ump.edu.my/id/eprint/4658/1/cd6635_80.pdf
first_indexed	2023-09-18T21:59:27Z
last_indexed	2023-09-18T21:59:27Z
_version_	1777414300088926208

Investigation of mig welding on dissimilar thickness of metal sheets (steel and stainless steel)

Similar Items