Modeling and simulation of the supersonic jet nozzle for oxygen injection system at electric arc furnace

Modeling and simulation of the supersonic jet nozzle for oxygen injection system at electric arc furnace

Bibliographic Details
Main Author:	Suhaimi, Mohd Sukri
Format:	Undergraduates Project Papers
Language:	English
Published:	2010
Subjects:	TP Chemical technology
Online Access:	http://umpir.ump.edu.my/id/eprint/3303/ http://umpir.ump.edu.my/id/eprint/3303/1/

Similar Items

Simulation of the supersonic jet length for KT oxygen lance with 22 mm diameter and 2:1 ratio of NG: O2 at electric arc furnace
by: Mohd Adam, Mohd Noor
Published: (2008)

Modelling of the supersonic jet length for KT oxygen lance with 15 cm diameter and 1:1 ratio of O2: NG at electric arc furnace using computational fluid dynamics (CFD)
by: Mohd khairul, Ya'kub
Published: (2008)

Modeling plastics injection molding operation using simulation
by: Li Mei, Tan
Published: (2014)

Wall Pressure Measurements Beneath the Supersonic Jets in an Abruptly Augmented Nozzle
by: Bashir, Musavir, et al.
Published: (2020)

Benchmarking of the actual injection of the product versus plastic simulation software
by: Zul Amri, A. Bakar
Published: (2008)

Base pressure control by supersonic micro jets in a suddenly expanded nozzle
by: Khan, Sher Afghan, et al.
Published: (2018)

Analysis of diesel spray characteristic using single hole SAC nozzle and VCO nozzle
by: Mohd Fazwan, Ishak
Published: (2012)

Analysis and prediction of injected parts by using mould filling simulation software
by: Nurul Farhanah, Rosli
Published: (2013)

Effects of materials selection on injection moulding parameters using moldflow simulation software
by: Mohd Nazri, Ismail
Published: (2009)

Analysis and prediction of micro injection molding part using moldflow simulation software
by: Mohammad Farhan, Othman
Published: (2012)

Influence of orifice nozzle geometry on flow and spray characteristics
by: Noor Azuani, Suliman
Published: (2013)

A study on the effect of injection moulding process parameters to the properties of injected parts
by: Sharifah Rafidah, Syed Hamid
Published: (2010)

Modeling and simulation of distillation column
by: Ann, Ivy Wong Fui
Published: (2014)

Design of Energy Efficient Distillation Columns for Separation of Oxygenates Process
by: Noor Asma Fazli, Abdul Samad, et al.
Published: (2014)

The use of laddle furnace slag in the treatment of contaminants water in acid mine drainage
by: Nur Athirah, Mohamad Basir, et al.
Published: (2019)

Analysis of emulsion fuel spray characteristics using SAC and VCO nozzle
by: Che Hanisah, Yaacob
Published: (2012)

Analysis of filling stage for injection molding
by: Muhammad Arshad, Zainol Abidin
Published: (2007)

Measurement of oxygen permeability in bulk alloys by internal oxidation of dilute constituent
by: Ani, Mohd Hanafi, et al.
Published: (2011)

A novel adsorbent formed from blast furnace slag by alkali fusion for phosphate ions removal / Takaaki Wajima
by: Wajima, Takaaki
Published: (2017)

Reduction of chemical oxygen demand (cod) using electrocoagulation in treating oleochemical wastewater
by: Abdul Aziz, Mohd Azoddein, et al.
Published: (2018)

Oxygen Vacancy-rich Mesoporous Silica KCC-1 for CO2 Methanation
by: M. Y. S., Hamid, et al.
Published: (2017)

Measurement and Prediction of Fuel Oxygenates Mixtures Excess Thermophysical Properties - A Review
by: T. K., Thanusha, et al.
Published: (2015)

Modeling and simulation of crude distillation unit (CDU)
by: Shu Yin, Oh
Published: (2014)

Influence of Nozzle Design on the Performance of a Partial Combustion Lance: A CFD Study
by: Law, Woon Phui, et al.
Published: (2015)

CFD Study On The Performance Of Oxygen Lance For Partial Combustion Unit At Direct Reduction Plant
by: Jolius, Gimbun, et al.
Published: (2011)

The study of coated nanoparticles injection in detection of hydrocarbon production
by: Mohd Zulkifli, Mohamad Noor, et al.
Published: (2019)

Development of a new wet gravity separator with jet flow
by: Ijichi, Ryota, et al.
Published: (2014)

Modelling and Simulation of Multi-vessel Batch Distillation Column
by: Nurul Hazwani, Sabri, et al.
Published: (2017)

A study of the spray characteristic for valve covered orifice diesel nozzle injector using CFD
by: Ahmad Aizuddin Faiz, Che Jaafar
Published: (2013)

CFD analysis of the supersonic nozzle flow with sudden expansion
by: Ahmed, Khizar Pathan, et al.
Published: (2016)

Effect of coupled catalyst loading and ionomer binder on oxygen reduction reaction in high-temperature pemfc
by: A. A., Jalil, et al.
Published: (2018)

A study of defects reduction in injection process of production line
by: Karen, Yap Chia Ern
Published: (2013)

Investigation and analysis of finding the injection molding gate by using moldflow
by: Muhamad Fridy Nizam, Harun
Published: (2007)

Conceptual design of two-plate injection mould for UMP's keychain
by: Azhar, Yusop
Published: (2008)

Modeling and Simulation of Steady State Model Approach for Horizontal Three Phase Separator (HTPS)
by: Bayu, Triwibowo, et al.
Published: (2017)

Modelling and simulation of fermentation product purification using batch distillation
by: Faezah, Bakar
Published: (2013)

A study of morphological effect of oxygen reduction catalyst on microbial fuel cell performance
by: Ravinder, Kumar
Published: (2017)

Study on the effect of ultrasound on oxygen uptake rate (gas-liquid mass transfer) of saccharomyces cerevisae fermentation
by: Noor Shahira, Saripa
Published: (2013)

Volumetric properties and leaching effect of asphalt mixes with electric arc furnace steel slag and copper mine tailings
by: Oluwasola, Ebenezer Akin, et al.
Published: (2016)

Sink marks defect on injection molding using different raw materials
by: Mohd Nazri, Noordin
Published: (2009)

Cannot write session to /tmp/vufind_sessions/sess_233n12la6a4tcvua17en05p4bh