Performance analysis of abrasive waterjet machining process at low pressure

Normally, a commercial waterjet cutting machine can generate water pressure up to 600 MPa. This range of pressure is used to machine a wide variety of materials. Hence, the price of waterjet cutting machine is expensive. Therefore, there is a need to develop a low cost waterjet machine in order to m...

Full description

Bibliographic Details
Main Authors:	M., Murugan, Mebrahitom, A., Azmir, Azhari, Zamzuri, Hamedon
Format:	Conference or Workshop Item
Language:	English English
Published:	Institute of Physics Publishing 2018
Subjects:	TS Manufactures
Online Access:	http://umpir.ump.edu.my/id/eprint/20465/ http://umpir.ump.edu.my/id/eprint/20465/ http://umpir.ump.edu.my/id/eprint/20465/1/Performance%20Analysis%20of%20Abrasive%20Waterjet%20Machining%20Process%20at%20Low%20Pressure.pdf http://umpir.ump.edu.my/id/eprint/20465/7/Performance%20Analysis%20of%20Abrasive%20Waterjet%20Machining%20Process%20at%20Low%20Pressure%201.pdf

id	ump-20465
recordtype	eprints
spelling	ump-204652018-05-21T06:25:17Z http://umpir.ump.edu.my/id/eprint/20465/ Performance analysis of abrasive waterjet machining process at low pressure M., Murugan Mebrahitom, A. Azmir, Azhari Zamzuri, Hamedon TS Manufactures Normally, a commercial waterjet cutting machine can generate water pressure up to 600 MPa. This range of pressure is used to machine a wide variety of materials. Hence, the price of waterjet cutting machine is expensive. Therefore, there is a need to develop a low cost waterjet machine in order to make the technology more accessible for the masses. Due to its low cost, such machines may only be able to generate water pressure at a much reduced rate. The present study attempts to investigate the performance of abrasive water jet machining process at low cutting pressure using self developed low cost waterjet machine. It aims to study the feasibility of machining various materials at low pressure which later can aid in further development of an effective low cost water jet machine. A total of three different materials were machined at a low pressure of 34 MPa. The materials are mild steel, aluminium alloy 6061 and plastics Delrin®. Furthermore, a traverse rate was varied between 1 to 3 mm/min. The study on cutting performance at low pressure for different materials was conducted in terms of depth penetration, kerf taper ratio and surface roughness. It was found that all samples were able to be machined at low cutting pressure with varied qualities. Also, the depth of penetration decreases with an increase in the traverse rate. Meanwhile, the surface roughness and kerf taper ratio increase with an increase in the traverse rate. It can be concluded that a low cost waterjet machine with a much reduced rate of water pressure can be successfully used for machining certain materials with acceptable qualities. Institute of Physics Publishing 2018-03 Conference or Workshop Item PeerReviewed application/pdf en http://umpir.ump.edu.my/id/eprint/20465/1/Performance%20Analysis%20of%20Abrasive%20Waterjet%20Machining%20Process%20at%20Low%20Pressure.pdf application/pdf en http://umpir.ump.edu.my/id/eprint/20465/7/Performance%20Analysis%20of%20Abrasive%20Waterjet%20Machining%20Process%20at%20Low%20Pressure%201.pdf M., Murugan and Mebrahitom, A. and Azmir, Azhari and Zamzuri, Hamedon (2018) Performance analysis of abrasive waterjet machining process at low pressure. In: 4th Asia Pacific Conference on Manufacturing Systems and the 3rd International Manufacturing Engineering Conference, APCOMS-iMEC 2017, 7-8 December 2017 , Yogyakarta, Indonesia. pp. 1-6., 319 (1). ISSN 17578981 http://iopscience.iop.org/article/10.1088/1757-899X/319/1/012051/pdf
repository_type	Digital Repository
institution_category	Local University
institution	Universiti Malaysia Pahang
building	UMP Institutional Repository
collection	Online Access
language	English English
topic	TS Manufactures
spellingShingle	TS Manufactures M., Murugan Mebrahitom, A. Azmir, Azhari Zamzuri, Hamedon Performance analysis of abrasive waterjet machining process at low pressure
description	Normally, a commercial waterjet cutting machine can generate water pressure up to 600 MPa. This range of pressure is used to machine a wide variety of materials. Hence, the price of waterjet cutting machine is expensive. Therefore, there is a need to develop a low cost waterjet machine in order to make the technology more accessible for the masses. Due to its low cost, such machines may only be able to generate water pressure at a much reduced rate. The present study attempts to investigate the performance of abrasive water jet machining process at low cutting pressure using self developed low cost waterjet machine. It aims to study the feasibility of machining various materials at low pressure which later can aid in further development of an effective low cost water jet machine. A total of three different materials were machined at a low pressure of 34 MPa. The materials are mild steel, aluminium alloy 6061 and plastics Delrin®. Furthermore, a traverse rate was varied between 1 to 3 mm/min. The study on cutting performance at low pressure for different materials was conducted in terms of depth penetration, kerf taper ratio and surface roughness. It was found that all samples were able to be machined at low cutting pressure with varied qualities. Also, the depth of penetration decreases with an increase in the traverse rate. Meanwhile, the surface roughness and kerf taper ratio increase with an increase in the traverse rate. It can be concluded that a low cost waterjet machine with a much reduced rate of water pressure can be successfully used for machining certain materials with acceptable qualities.
format	Conference or Workshop Item
author	M., Murugan Mebrahitom, A. Azmir, Azhari Zamzuri, Hamedon
author_facet	M., Murugan Mebrahitom, A. Azmir, Azhari Zamzuri, Hamedon
author_sort	M., Murugan
title	Performance analysis of abrasive waterjet machining process at low pressure
title_short	Performance analysis of abrasive waterjet machining process at low pressure
title_full	Performance analysis of abrasive waterjet machining process at low pressure
title_fullStr	Performance analysis of abrasive waterjet machining process at low pressure
title_full_unstemmed	Performance analysis of abrasive waterjet machining process at low pressure
title_sort	performance analysis of abrasive waterjet machining process at low pressure
publisher	Institute of Physics Publishing
publishDate	2018
url	http://umpir.ump.edu.my/id/eprint/20465/ http://umpir.ump.edu.my/id/eprint/20465/ http://umpir.ump.edu.my/id/eprint/20465/1/Performance%20Analysis%20of%20Abrasive%20Waterjet%20Machining%20Process%20at%20Low%20Pressure.pdf http://umpir.ump.edu.my/id/eprint/20465/7/Performance%20Analysis%20of%20Abrasive%20Waterjet%20Machining%20Process%20at%20Low%20Pressure%201.pdf
first_indexed	2023-09-18T22:29:31Z
last_indexed	2023-09-18T22:29:31Z
_version_	1777416191388680192

Performance analysis of abrasive waterjet machining process at low pressure

Similar Items