Mold design for plastics injection molding process (two colors) and analysis of gates location
This thesis describe about the mold design for plastic injection molding process for two colors and the analysis of gate location in order to find the best gate location to apply it in to the design. The molds for injection molding is not the cheap one it is expensive and needed an accurate step whe...
| id |
ump-16862 |
|---|---|
| recordtype |
eprints |
| spelling |
ump-168622017-04-10T00:16:38Z http://umpir.ump.edu.my/id/eprint/16862/ Mold design for plastics injection molding process (two colors) and analysis of gates location Ahmad Zulhelmi, Muhamad TP Chemical technology This thesis describe about the mold design for plastic injection molding process for two colors and the analysis of gate location in order to find the best gate location to apply it in to the design. The molds for injection molding is not the cheap one it is expensive and needed an accurate step when apply the design on the mold because a slice mistake can follow by big loss. First step is about finding the best gate location from several gate location have been choose but before that the design of the product and it materials should be choose. After the analysis have done, the collected data from several gate location will be compare in order to find best gate location and apply it in the mold design. To designing mold, the several system like runner system, injector system and the ways material enter the mold will be considered. 2009-11 Undergraduates Project Papers NonPeerReviewed application/pdf en http://umpir.ump.edu.my/id/eprint/16862/1/Mold%20design%20for%20plastics%20injection%20molding%20process%20%28two%20colors%29%20and%20analysis%20of%20gates%20location-Table%20of%20contents.pdf application/pdf en http://umpir.ump.edu.my/id/eprint/16862/25/Mold%20design%20for%20plastics%20injection%20molding%20process%20%28two%20colors%29%20and%20analysis%20of%20gates%20location%20-%20Abstract.pdf application/pdf en http://umpir.ump.edu.my/id/eprint/16862/13/Mold%20design%20for%20plastics%20injection%20molding%20process%20%28two%20colors%29%20and%20analysis%20of%20gates%20location-Chapter%201.pdf application/pdf en http://umpir.ump.edu.my/id/eprint/16862/19/Mold%20design%20for%20plastics%20injection%20molding%20process%20%28two%20colors%29%20and%20analysis%20of%20gates%20location-References.pdf Ahmad Zulhelmi, Muhamad (2009) Mold design for plastics injection molding process (two colors) and analysis of gates location. Faculty of Mechanical Engineering, Universiti Malaysia Pahang. http://iportal.ump.edu.my/lib/item?id=chamo:45504&theme=UMP2 |
| repository_type |
Digital Repository |
| institution_category |
Local University |
| institution |
Universiti Malaysia Pahang |
| building |
UMP Institutional Repository |
| collection |
Online Access |
| language |
English English English English |
| topic |
TP Chemical technology |
| spellingShingle |
TP Chemical technology Ahmad Zulhelmi, Muhamad Mold design for plastics injection molding process (two colors) and analysis of gates location |
| description |
This thesis describe about the mold design for plastic injection molding process for two colors and the analysis of gate location in order to find the best gate location to apply it in to the design. The molds for injection molding is not the cheap one it is expensive and needed an accurate step when apply the design on the mold because a slice mistake can follow by big loss. First step is about finding the best gate location from several gate location have been choose but before that the design of the product and it materials should be choose. After the analysis have done, the collected data from several gate location will be compare in order to find best gate location and apply it in the mold design. To designing mold, the several system like runner system, injector system and the ways material enter the mold will be considered. |
| format |
Undergraduates Project Papers |
| author |
Ahmad Zulhelmi, Muhamad |
| author_facet |
Ahmad Zulhelmi, Muhamad |
| author_sort |
Ahmad Zulhelmi, Muhamad |
| title |
Mold design for plastics injection molding process (two colors) and analysis of gates location |
| title_short |
Mold design for plastics injection molding process (two colors) and analysis of gates location |
| title_full |
Mold design for plastics injection molding process (two colors) and analysis of gates location |
| title_fullStr |
Mold design for plastics injection molding process (two colors) and analysis of gates location |
| title_full_unstemmed |
Mold design for plastics injection molding process (two colors) and analysis of gates location |
| title_sort |
mold design for plastics injection molding process (two colors) and analysis of gates location |
| publishDate |
2009 |
| url |
http://umpir.ump.edu.my/id/eprint/16862/ http://umpir.ump.edu.my/id/eprint/16862/ http://umpir.ump.edu.my/id/eprint/16862/1/Mold%20design%20for%20plastics%20injection%20molding%20process%20%28two%20colors%29%20and%20analysis%20of%20gates%20location-Table%20of%20contents.pdf http://umpir.ump.edu.my/id/eprint/16862/25/Mold%20design%20for%20plastics%20injection%20molding%20process%20%28two%20colors%29%20and%20analysis%20of%20gates%20location%20-%20Abstract.pdf http://umpir.ump.edu.my/id/eprint/16862/13/Mold%20design%20for%20plastics%20injection%20molding%20process%20%28two%20colors%29%20and%20analysis%20of%20gates%20location-Chapter%201.pdf http://umpir.ump.edu.my/id/eprint/16862/19/Mold%20design%20for%20plastics%20injection%20molding%20process%20%28two%20colors%29%20and%20analysis%20of%20gates%20location-References.pdf |
| first_indexed |
2023-09-18T22:22:53Z |
| last_indexed |
2023-09-18T22:22:53Z |
| _version_ |
1777415774808309760 |