Development of hot stamping tool by using indirect hot stamping for basic bending part (u-shape)
In hot stamping process, (UHSS) blank was cut into the rough shape. The blank is then heated to the temperature (900 - 950 °C) for 5 to 10 minutes inside the furnace. Then, the blank must be transferred quickly to the press to avoid the part is cooled before forming. After that, the blank is formed...
| Main Authors: | , |
|---|---|
| Format: | Bulletin |
| Language: | English |
| Published: |
2014
|
| Subjects: | |
| Online Access: | http://umpir.ump.edu.my/id/eprint/10805/ http://umpir.ump.edu.my/id/eprint/10805/1/DEVELOPMENT%20OF%20HOT%20STAMPING%20TOOL.pdf |
| id |
ump-10805 |
|---|---|
| recordtype |
eprints |
| spelling |
ump-108052019-03-14T07:07:01Z http://umpir.ump.edu.my/id/eprint/10805/ Development of hot stamping tool by using indirect hot stamping for basic bending part (u-shape) Mohd Fawzi, Zamri A. R., Yusoff TA Engineering (General). Civil engineering (General) TS Manufactures In hot stamping process, (UHSS) blank was cut into the rough shape. The blank is then heated to the temperature (900 - 950 °C) for 5 to 10 minutes inside the furnace. Then, the blank must be transferred quickly to the press to avoid the part is cooled before forming. After that, the blank is formed and cooled simultaneously by the water cooled die for 5 to lOs. Due to the contact between hot blank and the cool tool, the blank is cooled in the closed tool [1]. Today, hot stamping exists in two different types of methods which are direct and indirect. For indirect hot stamping method, before the blank is heated inside the furnace, it then undergoes cold pre-forming process. This process is done once after the blank is cut. 2014 Bulletin NonPeerReviewed pdf en http://umpir.ump.edu.my/id/eprint/10805/1/DEVELOPMENT%20OF%20HOT%20STAMPING%20TOOL.pdf Mohd Fawzi, Zamri and A. R., Yusoff (2014) Development of hot stamping tool by using indirect hot stamping for basic bending part (u-shape). Auto Inexss (7). ISSN 1985-8434 |
| repository_type |
Digital Repository |
| institution_category |
Local University |
| institution |
Universiti Malaysia Pahang |
| building |
UMP Institutional Repository |
| collection |
Online Access |
| language |
English |
| topic |
TA Engineering (General). Civil engineering (General) TS Manufactures |
| spellingShingle |
TA Engineering (General). Civil engineering (General) TS Manufactures Mohd Fawzi, Zamri A. R., Yusoff Development of hot stamping tool by using indirect hot stamping for basic bending part (u-shape) |
| description |
In hot stamping process, (UHSS) blank was cut into the rough shape. The blank is then heated to the temperature (900 - 950 °C) for 5 to 10 minutes inside the furnace. Then, the blank must be transferred quickly to the press to avoid the part is cooled before forming. After that, the
blank is formed and cooled simultaneously by the water cooled die for 5 to lOs. Due to the contact between hot blank and the cool tool, the blank is cooled in the closed tool [1]. Today, hot stamping exists in two different types of methods which are direct and indirect. For indirect hot stamping method, before the blank is heated inside the furnace, it then undergoes cold pre-forming process. This process is done once after the blank is cut. |
| format |
Bulletin |
| author |
Mohd Fawzi, Zamri A. R., Yusoff |
| author_facet |
Mohd Fawzi, Zamri A. R., Yusoff |
| author_sort |
Mohd Fawzi, Zamri |
| title |
Development of hot stamping tool by using indirect hot stamping for basic bending part (u-shape)
|
| title_short |
Development of hot stamping tool by using indirect hot stamping for basic bending part (u-shape)
|
| title_full |
Development of hot stamping tool by using indirect hot stamping for basic bending part (u-shape)
|
| title_fullStr |
Development of hot stamping tool by using indirect hot stamping for basic bending part (u-shape)
|
| title_full_unstemmed |
Development of hot stamping tool by using indirect hot stamping for basic bending part (u-shape)
|
| title_sort |
development of hot stamping tool by using indirect hot stamping for basic bending part (u-shape) |
| publishDate |
2014 |
| url |
http://umpir.ump.edu.my/id/eprint/10805/ http://umpir.ump.edu.my/id/eprint/10805/1/DEVELOPMENT%20OF%20HOT%20STAMPING%20TOOL.pdf |
| first_indexed |
2023-09-18T22:10:49Z |
| last_indexed |
2023-09-18T22:10:49Z |
| _version_ |
1777415015564836864 |