Effect of high-speed parameters on uncoated carbide tool in finish turning titanium Ti-6Al-4V ELI
In this work, the Sandvik uncoated carbide insert, CNGG 120408-SGF-H13A was used as a cutting tool in high-speed turning of titanium alloy Ti-6Al-4V ELI (extra-low interstitial) with hardness of 32 HRC. Wear is one of the problems that cannot be avoided in machining process. Therefore, the objective...
| Main Authors: | , , , |
|---|---|
| Format: | Article |
| Language: | English |
| Published: |
Universiti Kebangsaan Malaysia
2014
|
| Online Access: | http://journalarticle.ukm.my/6822/ http://journalarticle.ukm.my/6822/ http://journalarticle.ukm.my/6822/1/14_M.A._Sulaiman.pdf |
| id |
ukm-6822 |
|---|---|
| recordtype |
eprints |
| spelling |
ukm-68222016-12-14T06:42:17Z http://journalarticle.ukm.my/6822/ Effect of high-speed parameters on uncoated carbide tool in finish turning titanium Ti-6Al-4V ELI Sulaiman, M.A. Che Haron, C.H. Ghani, J.A. Kasim, M.S. In this work, the Sandvik uncoated carbide insert, CNGG 120408-SGF-H13A was used as a cutting tool in high-speed turning of titanium alloy Ti-6Al-4V ELI (extra-low interstitial) with hardness of 32 HRC. Wear is one of the problems that cannot be avoided in machining process. Therefore, the objective of this paper was to investigate tool-wear behavior of various cutting-speed values (high-speed range) on the tool life of the cutting tools, especially in finishing titanium alloy. The experiments were performed under flooded coolant condition using water-based mineral-oil. The cutting speeds employed were 120, 170 and 220 m/min. The feed rate was constant at 0.2 mm/rev and the depth of cut was 0.4 mm. Based on the results, the highest cutting speed of 220 m/min caused the highest wear rate. By linking the machine operations and the tool life curves obtained using flank wear data, the wear behavior of uncoated carbide was described. Universiti Kebangsaan Malaysia 2014-01 Article PeerReviewed application/pdf en http://journalarticle.ukm.my/6822/1/14_M.A._Sulaiman.pdf Sulaiman, M.A. and Che Haron, C.H. and Ghani, J.A. and Kasim, M.S. (2014) Effect of high-speed parameters on uncoated carbide tool in finish turning titanium Ti-6Al-4V ELI. Sains Malaysiana, 43 (1). pp. 111-116. ISSN 0126-6039 http://www.ukm.my/jsm/ |
| repository_type |
Digital Repository |
| institution_category |
Local University |
| institution |
Universiti Kebangasaan Malaysia |
| building |
UKM Institutional Repository |
| collection |
Online Access |
| language |
English |
| description |
In this work, the Sandvik uncoated carbide insert, CNGG 120408-SGF-H13A was used as a cutting tool in high-speed turning of titanium alloy Ti-6Al-4V ELI (extra-low interstitial) with hardness of 32 HRC. Wear is one of the problems that cannot be avoided in machining process. Therefore, the objective of this paper was to investigate tool-wear behavior of various cutting-speed values (high-speed range) on the tool life of the cutting tools, especially in finishing titanium alloy. The experiments were performed under flooded coolant condition using water-based mineral-oil. The cutting speeds employed were 120, 170 and 220 m/min. The feed rate was constant at 0.2 mm/rev and the depth of cut was 0.4 mm. Based on the results, the highest cutting speed of 220 m/min caused the highest wear rate. By linking the machine operations and the tool life curves obtained using flank wear data, the wear behavior of uncoated carbide was described. |
| format |
Article |
| author |
Sulaiman, M.A. Che Haron, C.H. Ghani, J.A. Kasim, M.S. |
| spellingShingle |
Sulaiman, M.A. Che Haron, C.H. Ghani, J.A. Kasim, M.S. Effect of high-speed parameters on uncoated carbide tool in finish turning titanium Ti-6Al-4V ELI |
| author_facet |
Sulaiman, M.A. Che Haron, C.H. Ghani, J.A. Kasim, M.S. |
| author_sort |
Sulaiman, M.A. |
| title |
Effect of high-speed parameters on uncoated carbide tool
in finish turning titanium Ti-6Al-4V ELI |
| title_short |
Effect of high-speed parameters on uncoated carbide tool
in finish turning titanium Ti-6Al-4V ELI |
| title_full |
Effect of high-speed parameters on uncoated carbide tool
in finish turning titanium Ti-6Al-4V ELI |
| title_fullStr |
Effect of high-speed parameters on uncoated carbide tool
in finish turning titanium Ti-6Al-4V ELI |
| title_full_unstemmed |
Effect of high-speed parameters on uncoated carbide tool
in finish turning titanium Ti-6Al-4V ELI |
| title_sort |
effect of high-speed parameters on uncoated carbide tool
in finish turning titanium ti-6al-4v eli |
| publisher |
Universiti Kebangsaan Malaysia |
| publishDate |
2014 |
| url |
http://journalarticle.ukm.my/6822/ http://journalarticle.ukm.my/6822/ http://journalarticle.ukm.my/6822/1/14_M.A._Sulaiman.pdf |
| first_indexed |
2023-09-18T19:47:59Z |
| last_indexed |
2023-09-18T19:47:59Z |
| _version_ |
1777406028844892160 |