Tool life of TiAlN PVD coated carbide tool in high-speed end milling of untreated inconel 718 under minimum quantity lubrication condition

This paper presents the tool life of the end milled Inconel 718, which is part of a material that is difficult to be machined. Previous researchers found that tool life in machining aged Inconel 718 is shorter compared with other materials. However, this observation required further investigation. T...

Full description

Bibliographic Details
Main Authors:	Kasim, M.S., Che Haron, C.H., Ghani, J.A., Gusri, A.I., Yazid, M.Z.A., Sulaiman, M.A.
Format:	Article
Language:	English
Published:	Universiti Kebangsaan Malaysia 2013
Online Access:	http://journalarticle.ukm.my/6681/ http://journalarticle.ukm.my/6681/ http://journalarticle.ukm.my/6681/1/05_M.S._Kasim.pdf

id	ukm-6681
recordtype	eprints
spelling	ukm-66812016-12-14T06:41:54Z http://journalarticle.ukm.my/6681/ Tool life of TiAlN PVD coated carbide tool in high-speed end milling of untreated inconel 718 under minimum quantity lubrication condition Kasim, M.S. Che Haron, C.H. Ghani, J.A. Gusri, A.I. Yazid, M.Z.A. Sulaiman, M.A. This paper presents the tool life of the end milled Inconel 718, which is part of a material that is difficult to be machined. Previous researchers found that tool life in machining aged Inconel 718 is shorter compared with other materials. However, this observation required further investigation. Thus, a raw grade Inconel was proposed in this experiment. The experiments were performed using TiAlN-coated carbide. The studied milling parameters were the cutting speed, Vc, from 90 to 150 m/min; feed rate, fz, from 0.15 to 0.25 mm/rev; depth of cut, ap, from 0.3 to 0.5 mm; and radial depth of cut, ae=1 mm. The application of the cutting fluid used in this experiment was a minimum quantity lubricant, which had the advantage of cooling effectiveness and low consumption of cutting fluid. The results showed that the feed rate, fz, was the primary factor controlling the tool life. The combination of Vc=115 m/min, fz=0.15 mm/tooth, as well as ap=0.5 mm and ae=0.15 mm gave the longest tool life that served 95.38 min in operation. Universiti Kebangsaan Malaysia 2013-12 Article PeerReviewed application/pdf en http://journalarticle.ukm.my/6681/1/05_M.S._Kasim.pdf Kasim, M.S. and Che Haron, C.H. and Ghani, J.A. and Gusri, A.I. and Yazid, M.Z.A. and Sulaiman, M.A. (2013) Tool life of TiAlN PVD coated carbide tool in high-speed end milling of untreated inconel 718 under minimum quantity lubrication condition. Sains Malaysiana, 42 (12). pp. 1721-1726. ISSN 0126-6039 http://www.ukm.my/jsm/
repository_type	Digital Repository
institution_category	Local University
institution	Universiti Kebangasaan Malaysia
building	UKM Institutional Repository
collection	Online Access
language	English
description	This paper presents the tool life of the end milled Inconel 718, which is part of a material that is difficult to be machined. Previous researchers found that tool life in machining aged Inconel 718 is shorter compared with other materials. However, this observation required further investigation. Thus, a raw grade Inconel was proposed in this experiment. The experiments were performed using TiAlN-coated carbide. The studied milling parameters were the cutting speed, Vc, from 90 to 150 m/min; feed rate, fz, from 0.15 to 0.25 mm/rev; depth of cut, ap, from 0.3 to 0.5 mm; and radial depth of cut, ae=1 mm. The application of the cutting fluid used in this experiment was a minimum quantity lubricant, which had the advantage of cooling effectiveness and low consumption of cutting fluid. The results showed that the feed rate, fz, was the primary factor controlling the tool life. The combination of Vc=115 m/min, fz=0.15 mm/tooth, as well as ap=0.5 mm and ae=0.15 mm gave the longest tool life that served 95.38 min in operation.
format	Article
author	Kasim, M.S. Che Haron, C.H. Ghani, J.A. Gusri, A.I. Yazid, M.Z.A. Sulaiman, M.A.
spellingShingle	Kasim, M.S. Che Haron, C.H. Ghani, J.A. Gusri, A.I. Yazid, M.Z.A. Sulaiman, M.A. Tool life of TiAlN PVD coated carbide tool in high-speed end milling of untreated inconel 718 under minimum quantity lubrication condition
author_facet	Kasim, M.S. Che Haron, C.H. Ghani, J.A. Gusri, A.I. Yazid, M.Z.A. Sulaiman, M.A.
author_sort	Kasim, M.S.
title	Tool life of TiAlN PVD coated carbide tool in high-speed end milling of untreated inconel 718 under minimum quantity lubrication condition
title_short	Tool life of TiAlN PVD coated carbide tool in high-speed end milling of untreated inconel 718 under minimum quantity lubrication condition
title_full	Tool life of TiAlN PVD coated carbide tool in high-speed end milling of untreated inconel 718 under minimum quantity lubrication condition
title_fullStr	Tool life of TiAlN PVD coated carbide tool in high-speed end milling of untreated inconel 718 under minimum quantity lubrication condition
title_full_unstemmed	Tool life of TiAlN PVD coated carbide tool in high-speed end milling of untreated inconel 718 under minimum quantity lubrication condition
title_sort	tool life of tialn pvd coated carbide tool in high-speed end milling of untreated inconel 718 under minimum quantity lubrication condition
publisher	Universiti Kebangsaan Malaysia
publishDate	2013
url	http://journalarticle.ukm.my/6681/ http://journalarticle.ukm.my/6681/ http://journalarticle.ukm.my/6681/1/05_M.S._Kasim.pdf
first_indexed	2023-09-18T19:47:35Z
last_indexed	2023-09-18T19:47:35Z
_version_	1777406003290046464

Tool life of TiAlN PVD coated carbide tool in high-speed end milling of untreated inconel 718 under minimum quantity lubrication condition

Similar Items