Characterization of metal injection molding (MIM) feedstock based on water soluble binder system

Characterization of metal injection molding (MIM) feedstock based on water soluble binder system

Bibliographic Details
Main Authors:	Muhamad Hussain Ismail, Norhamidi Muhamad, Mohd Afian Omar
Format:	Article
Language:	English
Published:	2008
Online Access:	http://journalarticle.ukm.my/2554/ http://journalarticle.ukm.my/2554/ http://journalarticle.ukm.my/2554/1/2008-2.pdf

Similar Items

Characterization of the feedstock properties of metal injection-molded WC-Co with palm stearin binder system
by: Sri Yulis M. Amin,, et al.
Published: (2014)

The effects of various TPNR binder compositions on feedstock preparation for MIM process
by: Hassan, Norita, et al.
Published: (2015)

Morphology and mechanical properties of MIM feedstock using TPNR backbone binder
by: Hassan, Norita, et al.
Published: (2015)

Optimization of injection molding and solvent debinding parameters of stainless steel powder (SS316L) based feedstock for metal injection molding
by: Muhammad Ilman Hakimi Chua,, et al.
Published: (2013)

Homogenous feedstock for metal injection molding (MIM) process / Yusb Ishaq Mohamad and Mior Sharul Nizam Mior Ahmad
by: Mohamad, Yusb Ishaq, et al.
Published: (2004)

Preparation of SS316L MIM feedstock with biopolymer as a binder
by: Abdullah, Abu, et al.
Published: (2018)

Fabrication of metallic implants using palm based binder through MIM process
by: Omar, Mohd Afian, et al.
Published: (2011)

Feedstock preparation of injection moulded stainless steel using biodegradable starch binder
by: Omar, Mohd Afian, et al.
Published: (2011)

Thermoplastic natural rubber (TPNR) as a backbone polymer for metal injection molding
by: Norita Hassan,, et al.
Published: (2013)

Study on stability of a novel binder system based on palm stearin in metal injection moulding application / Muhammad Hussain Ismail ... [et al.]
by: Ismail, Muhammad Hussain, et al.
Published: (2007)

Characterization of newly developed feedstock in metal injection moulding application using titanium mix with palm stearin binder system / Nor Hafiez Mohamad Nor , Muhammad Hussain Ismail and Prof. Dr. Norhamidi Muhamad
by: Mohamad Nor, Nor Hafiez, et al.
Published: (2011)

Moldability characteristics of 3 mol% Yttria Stabilized Zirconia feedstock for micro-powder injection molding process
by: Hafizawati Zakaria,, et al.
Published: (2014)

Development of thermoplastic natural rubber (TPNR) as a new binder in metal injection moulding
by: Omar, Mohd Afian, et al.
Published: (2016)

Effect of mixing process parameters and suitability of backbone polymer for aluminum powder injection molding feedstock
by: A.A. Abdullahi,, et al.
Published: (2017)

Investigations on metal injection molding of 316L SS using Thermoplastic Natural Rubber (TPNR) binder as a new system
by: Hassan, Norita, et al.
Published: (2012)

Mold design for plastics injection molding process (two colors) and analysis of gates location
by: Ahmad Zulhelmi, Muhamad
Published: (2009)

Study on the novel binder based biodegradable polyhyroxyalkanoates (PHA) for metal injection moulding application
by: Hassan, Norita
Published: (2018)

Understanding injection molding technology
by: Rees 1915-
Published: (1994)

Fabrication of microcomponents by injection molding
by: Yuan , S., et al.
Published: (2004)

Simulation of micro-injection molding
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Investigation and analysis of finding the injection molding gate by using moldflow
by: Muhamad Fridy Nizam, Harun
Published: (2007)

Analysis of filling stage for injection molding
by: Muhammad Arshad, Zainol Abidin
Published: (2007)

Plastic part design for injection molding an introduction
by: Malloy
Published: (1994)

Metal injection moulding of hip stem CoCrMo alloy powder using palm stearin binder system
by: Omar, Mohd Afian, et al.
Published: (2016)

Effects of vanadium carbide on sintered WC-10%Co produced by micro-powder injection molding
by: Wong, Yee Ning, et al.
Published: (2015)

Phase transformation temperatures (PPTs) and microstructure of moulded NiTi alloy using a water soluble binder system
by: Muhammad Hussain Ismail,, et al.
Published: (2013)

Hot embossing and injection molding of three-dimensional microcomponents
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

Modeling plastics injection molding operation using simulation
by: Li Mei, Tan
Published: (2014)

Effects of debinding and sintering atmosphere on properties and corrosion resistance of powder injection molded 316 L - stainless steel
by: Raza, Muhammad Rafi, et al.
Published: (2017)

Effect of space holders on fabrication of porous titanium alloy-hydroxyapatite composite through powder injection molding
by: Farrahshaida Mohd Salleh,, et al.
Published: (2017)

Experimental and numerical studies on superhigh strengthening sintered low alloy steels fabricated by metal injection molding)
by: Wan Sharuzi, Wan Harun
Published: (2013)

Simulation on effect of preform diameter in injection stretch blow molding
by: Tan, Z Q, et al.
Published: (2018)

Effect of Binders on Physical and Mechanical Properties of Stainless Steel 316L Alloy Fabricated by Metal Injection Moulding Process
by: Mohd Faizul Farhan, Ahmad Hamidi, et al.
Published: (2016)

Physical and mechanical properties of injection molded co-cr-mo alloy powder for orthopedic applications
by: Johari, Nurhaslina, et al.
Published: (2016)

Fracture fixation plate for fracture healing comparing 316L stainless steel by metal injection molding technique plate with convantional plate in rabbit fracture model
by: Zulkifly, Ahmad Hafiz, et al.
Published: (2011)

Optimization of process parameters of injection moldings for plastic pallets manufacturing industry
by: Vivekanandan, Panneerselvam, et al.
Published: (2019)

Modeling and Flow Analysis of Pure Nylon Polymer for Injection Molding Process
by: Nuruzzaman, D. M., et al.
Published: (2016)

A new material supply mechanism for plunger type injection molding
by: Mohd Syahmi, Mohd Nong
Published: (2013)

Sink marks defect on injection molding using different raw materials
by: Mohd Nazri, Noordin
Published: (2009)

Improvement in thermomechanical properties of injection molded nano-modified hybrid biocomposite
by: Kaiser, Mohammad Rejaul, et al.
Published: (2014)

Cannot write session to /tmp/vufind_sessions/sess_j4ahqjhaff97objm5h2en84kin