Design and implementation of a real-time adaptive learning algorithm controller for a 3-DOF parallel manipulator / Mustafa Jabbar Hayawi

A parallel manipulator is a closed loop mechanism which consists of a moving platform that is connected to a fixed base by at least two kinematic chains in parallel. Parallel manipulators can provide several advantages, such as high stiffness, high accuracy, and low inertia but also have some disadv...

Full description

Bibliographic Details
Main Author:	Hayawi, Mustafa Jabbar
Format:	Thesis
Language:	English
Published:	2015
Subjects:	Robotics. Robots. Manipulators (Mechanism)
Online Access:	http://ir.uitm.edu.my/id/eprint/21610/ http://ir.uitm.edu.my/id/eprint/21610/1/TP_MUSTAFA%20JABBAR%20HAYAWI%20EM%2015_5.pdf

id	uitm-21610
recordtype	eprints
spelling	uitm-216102018-09-27T02:22:55Z http://ir.uitm.edu.my/id/eprint/21610/ Design and implementation of a real-time adaptive learning algorithm controller for a 3-DOF parallel manipulator / Mustafa Jabbar Hayawi Hayawi, Mustafa Jabbar Robotics. Robots. Manipulators (Mechanism) A parallel manipulator is a closed loop mechanism which consists of a moving platform that is connected to a fixed base by at least two kinematic chains in parallel. Parallel manipulators can provide several advantages, such as high stiffness, high accuracy, and low inertia but also have some disadvantages, such as small workspace, complicated structures, a high cost, and also pose a major challenge to their analysis and control. To overcome the above shortcomings, progress on the development of parallel manipulators with less than 6-DOF has been accelerated. In this thesis, a new parallel manipulator with three degrees of freedom DOF is designed. Kinematic of the manipulator including inverse kinematic, Jacobian matrix and velocity equation are analyzed. Performance indices such as workspace, dexterity and stiffness, of the parallel manipulator are studied. The parallel manipulator is optimized based on the performance indices to obtain on the optimal design parameters for achieved maximum performance of the parallel manipulator. A prototype was fabricated to demonstrate the manipulator. An electronic board, transistor relay driver circuit, is designed for the purpose of establishing communication interface between the computer, adaptive learning algorithm and the actuator mechanism. Design and development an adaptive learning algorithm controller ALAC of position the actuators is presented in real time parallel manipulator based on artificial neural network ANN. The control of a parallel manipulator based on joint space control is implemented by determine the lengths of the electrohydraulic actuators EHA individually. EHA are known to have nonlinear parameters and dynamic factors such as frictions, load variations and leakage. These effects, if not controlled, would lead to large scale oscillations that would damage system components. System identification is a prerequisite to analysis of a dynamic system. It is performed using neural network Auto Regressive with exogenous (NNARX) model based on the input/ output experimental data. There some criteria such as loss function, Aikeke's Information Criterion, goodness of fit and correlation analysis of the residual are analyzed to determine the adequate model for representing the EHA. The real time ALAC is coded in MATLAB/ SIMULINK and consists of two inverse ANN, feed forward neural network ANN1 and feedback network ANN2, and proportional feedback controller (P). The ANN2 is used to update the weights and biases online while ANN1 is used to implement the controller. Pcontroller is designed to improve the controller system and ensure the stability. The updated weights and biases of the ANN1 are same set obtained ANN2. The results of the proposed controller were compared with direct inverse neural controller DINC. It was found from experimentation that the ALAC was able to improve the position control of the parallel manipulator and adjusted the weights according to changing condition and control the system without any changes in the controlling algorithm. It is still effective with few overshoot compared with DINC. 2015 Thesis NonPeerReviewed text en http://ir.uitm.edu.my/id/eprint/21610/1/TP_MUSTAFA%20JABBAR%20HAYAWI%20EM%2015_5.pdf Hayawi, Mustafa Jabbar (2015) Design and implementation of a real-time adaptive learning algorithm controller for a 3-DOF parallel manipulator / Mustafa Jabbar Hayawi. PhD thesis, Universiti Teknologi MARA.
repository_type	Digital Repository
institution_category	Local University
institution	Universiti Teknologi MARA
building	UiTM Institutional Repository
collection	Online Access
language	English
topic	Robotics. Robots. Manipulators (Mechanism)
spellingShingle	Robotics. Robots. Manipulators (Mechanism) Hayawi, Mustafa Jabbar Design and implementation of a real-time adaptive learning algorithm controller for a 3-DOF parallel manipulator / Mustafa Jabbar Hayawi
description	A parallel manipulator is a closed loop mechanism which consists of a moving platform that is connected to a fixed base by at least two kinematic chains in parallel. Parallel manipulators can provide several advantages, such as high stiffness, high accuracy, and low inertia but also have some disadvantages, such as small workspace, complicated structures, a high cost, and also pose a major challenge to their analysis and control. To overcome the above shortcomings, progress on the development of parallel manipulators with less than 6-DOF has been accelerated. In this thesis, a new parallel manipulator with three degrees of freedom DOF is designed. Kinematic of the manipulator including inverse kinematic, Jacobian matrix and velocity equation are analyzed. Performance indices such as workspace, dexterity and stiffness, of the parallel manipulator are studied. The parallel manipulator is optimized based on the performance indices to obtain on the optimal design parameters for achieved maximum performance of the parallel manipulator. A prototype was fabricated to demonstrate the manipulator. An electronic board, transistor relay driver circuit, is designed for the purpose of establishing communication interface between the computer, adaptive learning algorithm and the actuator mechanism. Design and development an adaptive learning algorithm controller ALAC of position the actuators is presented in real time parallel manipulator based on artificial neural network ANN. The control of a parallel manipulator based on joint space control is implemented by determine the lengths of the electrohydraulic actuators EHA individually. EHA are known to have nonlinear parameters and dynamic factors such as frictions, load variations and leakage. These effects, if not controlled, would lead to large scale oscillations that would damage system components. System identification is a prerequisite to analysis of a dynamic system. It is performed using neural network Auto Regressive with exogenous (NNARX) model based on the input/ output experimental data. There some criteria such as loss function, Aikeke's Information Criterion, goodness of fit and correlation analysis of the residual are analyzed to determine the adequate model for representing the EHA. The real time ALAC is coded in MATLAB/ SIMULINK and consists of two inverse ANN, feed forward neural network ANN1 and feedback network ANN2, and proportional feedback controller (P). The ANN2 is used to update the weights and biases online while ANN1 is used to implement the controller. Pcontroller is designed to improve the controller system and ensure the stability. The updated weights and biases of the ANN1 are same set obtained ANN2. The results of the proposed controller were compared with direct inverse neural controller DINC. It was found from experimentation that the ALAC was able to improve the position control of the parallel manipulator and adjusted the weights according to changing condition and control the system without any changes in the controlling algorithm. It is still effective with few overshoot compared with DINC.
format	Thesis
author	Hayawi, Mustafa Jabbar
author_facet	Hayawi, Mustafa Jabbar
author_sort	Hayawi, Mustafa Jabbar
title	Design and implementation of a real-time adaptive learning algorithm controller for a 3-DOF parallel manipulator / Mustafa Jabbar Hayawi
title_short	Design and implementation of a real-time adaptive learning algorithm controller for a 3-DOF parallel manipulator / Mustafa Jabbar Hayawi
title_full	Design and implementation of a real-time adaptive learning algorithm controller for a 3-DOF parallel manipulator / Mustafa Jabbar Hayawi
title_fullStr	Design and implementation of a real-time adaptive learning algorithm controller for a 3-DOF parallel manipulator / Mustafa Jabbar Hayawi
title_full_unstemmed	Design and implementation of a real-time adaptive learning algorithm controller for a 3-DOF parallel manipulator / Mustafa Jabbar Hayawi
title_sort	design and implementation of a real-time adaptive learning algorithm controller for a 3-dof parallel manipulator / mustafa jabbar hayawi
publishDate	2015
url	http://ir.uitm.edu.my/id/eprint/21610/ http://ir.uitm.edu.my/id/eprint/21610/1/TP_MUSTAFA%20JABBAR%20HAYAWI%20EM%2015_5.pdf
first_indexed	2023-09-18T23:06:56Z
last_indexed	2023-09-18T23:06:56Z
_version_	1777418545977622528

Design and implementation of a real-time adaptive learning algorithm controller for a 3-DOF parallel manipulator / Mustafa Jabbar Hayawi

Similar Items