Flank wear analysing of high speed end milling for hardened steel D2 using Taguchi method

One of the main challenges for any manufacturer is how to decrease the machining cost without affecting the final quality of the product. One of the new advanced machining processes in industry is the high speed hard end milling process that merges three advanced machining processes: high speed mill...

Full description

Bibliographic Details
Main Authors:	Al Hazza, Muataz Hazza Faizi, Ibrahim, Nur Asmawiyah, Adesta, Erry Yulian Triblas, Khan, Ahsan Ali, Abdullah Sidek, 'Atiah
Format:	Article
Language:	English English
Published:	IOP Publishing 2017
Subjects:	TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/56336/ http://irep.iium.edu.my/56336/ http://irep.iium.edu.my/56336/ http://irep.iium.edu.my/56336/1/5.pdf http://irep.iium.edu.my/56336/7/Flank%20wear%20analysing%20of%20high%20speed%20end%20milling%20for%20hardened%20steel%20D2%20using%20Taguchi%20method.pdf

id	iium-56336
recordtype	eprints
spelling	iium-563362018-01-16T02:15:32Z http://irep.iium.edu.my/56336/ Flank wear analysing of high speed end milling for hardened steel D2 using Taguchi method Al Hazza, Muataz Hazza Faizi Ibrahim, Nur Asmawiyah Adesta, Erry Yulian Triblas Khan, Ahsan Ali Abdullah Sidek, 'Atiah TS200 Metal manufactures. Metalworking One of the main challenges for any manufacturer is how to decrease the machining cost without affecting the final quality of the product. One of the new advanced machining processes in industry is the high speed hard end milling process that merges three advanced machining processes: high speed milling, hard milling and dry milling. However, one of the most important challenges in this process is to control the flank wear rate. Therefore a analyzing the flank wear rate during machining should be investigated in order to determine the best cutting levels that will not affect the final quality of the product. In this research Taguchi method has been used to investigate the effect of cutting speed, feed rate and depth of cut and determine the best level s to minimize the flank wear rate up to total length of 0.3mm based on the ISO standard to maintain the finishing requirements. IOP Publishing 2017-04 Article PeerReviewed application/pdf en http://irep.iium.edu.my/56336/1/5.pdf application/pdf en http://irep.iium.edu.my/56336/7/Flank%20wear%20analysing%20of%20high%20speed%20end%20milling%20for%20hardened%20steel%20D2%20using%20Taguchi%20method.pdf Al Hazza, Muataz Hazza Faizi and Ibrahim, Nur Asmawiyah and Adesta, Erry Yulian Triblas and Khan, Ahsan Ali and Abdullah Sidek, 'Atiah (2017) Flank wear analysing of high speed end milling for hardened steel D2 using Taguchi method. IOP Conference Series: Materials Science and Engineering, 184. pp. 1-5. ISSN 1757-899X http://iopscience.iop.org/article/10.1088/1757-899X/184/1/012048/pdf 10.1088/1757-899X/184/1/012048
repository_type	Digital Repository
institution_category	Local University
institution	International Islamic University Malaysia
building	IIUM Repository
collection	Online Access
language	English English
topic	TS200 Metal manufactures. Metalworking
spellingShingle	TS200 Metal manufactures. Metalworking Al Hazza, Muataz Hazza Faizi Ibrahim, Nur Asmawiyah Adesta, Erry Yulian Triblas Khan, Ahsan Ali Abdullah Sidek, 'Atiah Flank wear analysing of high speed end milling for hardened steel D2 using Taguchi method
description	One of the main challenges for any manufacturer is how to decrease the machining cost without affecting the final quality of the product. One of the new advanced machining processes in industry is the high speed hard end milling process that merges three advanced machining processes: high speed milling, hard milling and dry milling. However, one of the most important challenges in this process is to control the flank wear rate. Therefore a analyzing the flank wear rate during machining should be investigated in order to determine the best cutting levels that will not affect the final quality of the product. In this research Taguchi method has been used to investigate the effect of cutting speed, feed rate and depth of cut and determine the best level s to minimize the flank wear rate up to total length of 0.3mm based on the ISO standard to maintain the finishing requirements.
format	Article
author	Al Hazza, Muataz Hazza Faizi Ibrahim, Nur Asmawiyah Adesta, Erry Yulian Triblas Khan, Ahsan Ali Abdullah Sidek, 'Atiah
author_facet	Al Hazza, Muataz Hazza Faizi Ibrahim, Nur Asmawiyah Adesta, Erry Yulian Triblas Khan, Ahsan Ali Abdullah Sidek, 'Atiah
author_sort	Al Hazza, Muataz Hazza Faizi
title	Flank wear analysing of high speed end milling for hardened steel D2 using Taguchi method
title_short	Flank wear analysing of high speed end milling for hardened steel D2 using Taguchi method
title_full	Flank wear analysing of high speed end milling for hardened steel D2 using Taguchi method
title_fullStr	Flank wear analysing of high speed end milling for hardened steel D2 using Taguchi method
title_full_unstemmed	Flank wear analysing of high speed end milling for hardened steel D2 using Taguchi method
title_sort	flank wear analysing of high speed end milling for hardened steel d2 using taguchi method
publisher	IOP Publishing
publishDate	2017
url	http://irep.iium.edu.my/56336/ http://irep.iium.edu.my/56336/ http://irep.iium.edu.my/56336/ http://irep.iium.edu.my/56336/1/5.pdf http://irep.iium.edu.my/56336/7/Flank%20wear%20analysing%20of%20high%20speed%20end%20milling%20for%20hardened%20steel%20D2%20using%20Taguchi%20method.pdf
first_indexed	2023-09-18T21:19:28Z
last_indexed	2023-09-18T21:19:28Z
_version_	1777411784117846016

Flank wear analysing of high speed end milling for hardened steel D2 using Taguchi method

Similar Items