TIG melted surface modified titanium alloy for cylinder liner application
Tungsten inert gas (TIG) surface modification with Fe-based alloy can give protection against wear and corrosion of metallic component material. In this study, an attempt has been made to explore deposition of Fe-based alloy on commercial purity titanium (CP-Ti) by TIG torch melting process to imp...
| Main Authors: | , |
|---|---|
| Format: | Article |
| Language: | English |
| Published: |
Academic @ Paper
2015
|
| Subjects: | |
| Online Access: | http://irep.iium.edu.my/49712/ http://irep.iium.edu.my/49712/ http://irep.iium.edu.my/49712/1/P108_2015_IJAET_Adeleke.pdf |
| id |
iium-49712 |
|---|---|
| recordtype |
eprints |
| spelling |
iium-497122020-03-04T02:57:11Z http://irep.iium.edu.my/49712/ TIG melted surface modified titanium alloy for cylinder liner application Adeleke, S. A. Maleque, Md. Abdul T173.2 Technological change TA401 Materials of engineering and construction TN600 Metallurgy Tungsten inert gas (TIG) surface modification with Fe-based alloy can give protection against wear and corrosion of metallic component material. In this study, an attempt has been made to explore deposition of Fe-based alloy on commercial purity titanium (CP-Ti) by TIG torch melting process to improve resistance of substrate to wear. Three different powder blends with nominal composition of 97Fe2C1Si, 94Fe 4C2Si and 91Fe6C3Si were separately melted on CP-Ti using a conventional TIG welding torch produced at 100 A and energy input 1350 J/mm. Analysis of the results showed that TIG torch produced melt pools geometry with good metallurgical bonding with the substrate. The melt microstructures consisted of variety of different TiC precipitates. Pores were conspicuously seen on the melt microstructure modified with highest carbon content. Both micro hardness and wear resistance showed a significant improvement particularly after TIG coating with 94Fe4C2Si. Thus, it appears that an optimized composition of TIG coated with 94Fe4C2Si was best to control abrasive resistance and for the application of cylindrical liner. Academic @ Paper 2015 Article PeerReviewed application/pdf en http://irep.iium.edu.my/49712/1/P108_2015_IJAET_Adeleke.pdf Adeleke, S. A. and Maleque, Md. Abdul (2015) TIG melted surface modified titanium alloy for cylinder liner application. International Journal of Automotive Engineering and Technologies, 4 (3). pp. 130-138. ISSN 2146-9067 http://ijaet.academicpaper.org/article/view/1072000109 |
| repository_type |
Digital Repository |
| institution_category |
Local University |
| institution |
International Islamic University Malaysia |
| building |
IIUM Repository |
| collection |
Online Access |
| language |
English |
| topic |
T173.2 Technological change TA401 Materials of engineering and construction TN600 Metallurgy |
| spellingShingle |
T173.2 Technological change TA401 Materials of engineering and construction TN600 Metallurgy Adeleke, S. A. Maleque, Md. Abdul TIG melted surface modified titanium alloy for cylinder liner application |
| description |
Tungsten inert gas (TIG) surface modification with Fe-based alloy can give protection against wear and
corrosion of metallic component material. In this study, an attempt has been made to explore deposition
of Fe-based alloy on commercial purity titanium (CP-Ti) by TIG torch melting process to improve
resistance of substrate to wear. Three different powder blends with nominal composition of 97Fe2C1Si,
94Fe 4C2Si and 91Fe6C3Si were separately melted on CP-Ti using a conventional TIG welding torch
produced at 100 A and energy input 1350 J/mm. Analysis of the results showed that TIG torch
produced melt pools geometry with good metallurgical bonding with the substrate. The melt
microstructures consisted of variety of different TiC precipitates. Pores were conspicuously seen on the
melt microstructure modified with highest carbon content. Both micro hardness and wear resistance
showed a significant improvement particularly after TIG coating with 94Fe4C2Si. Thus, it appears that
an optimized composition of TIG coated with 94Fe4C2Si was best to control abrasive resistance and for
the application of cylindrical liner.
|
| format |
Article |
| author |
Adeleke, S. A. Maleque, Md. Abdul |
| author_facet |
Adeleke, S. A. Maleque, Md. Abdul |
| author_sort |
Adeleke, S. A. |
| title |
TIG melted surface modified titanium alloy for cylinder liner application |
| title_short |
TIG melted surface modified titanium alloy for cylinder liner application |
| title_full |
TIG melted surface modified titanium alloy for cylinder liner application |
| title_fullStr |
TIG melted surface modified titanium alloy for cylinder liner application |
| title_full_unstemmed |
TIG melted surface modified titanium alloy for cylinder liner application |
| title_sort |
tig melted surface modified titanium alloy for cylinder liner application |
| publisher |
Academic @ Paper |
| publishDate |
2015 |
| url |
http://irep.iium.edu.my/49712/ http://irep.iium.edu.my/49712/ http://irep.iium.edu.my/49712/1/P108_2015_IJAET_Adeleke.pdf |
| first_indexed |
2023-09-18T21:10:15Z |
| last_indexed |
2023-09-18T21:10:15Z |
| _version_ |
1777411204862443520 |