Tool wear and surface roughness on milling carbon fiber-reinforced plastic using chilled air

Tool wear and surface roughness on milling carbon fiber-reinforced plastic using chilled air

Carbon fiber-reinforced plastic (CFRP) composite is an expensive material that is widely used in aerospace applications because of its unique properties. During machining, several problems arise because of the carbon in CFRP. Abrasive wear occurs on the cutting tools during CFRP machining, thereby s...

Full description

Bibliographic Details
Main Authors: Muhamad Khairussaleh, Nor Khairusshima, C.H., Che Hassan, A.Ghani, Jaharah, A.K.M., Nurul Amin
Format: Article
Language:English
Published: Asian Economic and Social Society 2012
Subjects:
T Technology (General)
Online Access:http://irep.iium.edu.my/48609/
http://irep.iium.edu.my/48609/
http://irep.iium.edu.my/48609/1/asian_pacific.pdf
id iium-48609
recordtype eprints
spelling iium-486092016-07-18T00:56:45Z http://irep.iium.edu.my/48609/ Tool wear and surface roughness on milling carbon fiber-reinforced plastic using chilled air Muhamad Khairussaleh, Nor Khairusshima C.H., Che Hassan A.Ghani, Jaharah A.K.M., Nurul Amin T Technology (General) Carbon fiber-reinforced plastic (CFRP) composite is an expensive material that is widely used in aerospace applications because of its unique properties. During machining, several problems arise because of the carbon in CFRP. Abrasive wear occurs on the cutting tools during CFRP machining, thereby shortening the life of the tools and damaging surface quality. In this study, the performance of the solid carbide end tool and the surface quality of CFRP composite during the milling process were investigated. A cutting speed ranging from 160 m/min to 200 m/min and a feed rate ranging from 0.025 mm/rev to 0.05 mm/rev were used in the experiment. Results show that tool wear is higher at higher feed rates and lower cutting speeds, whereas longer tool life is achieved at lower feed rates and intermediate cutting speeds. Furthermore, a good machined surface is produced at higher cutting speeds and higher feed rates. Asian Economic and Social Society 2012 Article PeerReviewed application/pdf en http://irep.iium.edu.my/48609/1/asian_pacific.pdf Muhamad Khairussaleh, Nor Khairusshima and C.H., Che Hassan and A.Ghani, Jaharah and A.K.M., Nurul Amin (2012) Tool wear and surface roughness on milling carbon fiber-reinforced plastic using chilled air. Journal of Asian Scientific Research, 2 (11). pp. 593-598. ISSN 2226-5724 E-ISSN 2223-1331 http://www.aessweb.com/journals/5003/November2012
repository_type Digital Repository
institution_category Local University
institution International Islamic University Malaysia
building IIUM Repository
collection Online Access
language English
topic T Technology (General)
spellingShingle T Technology (General)
Muhamad Khairussaleh, Nor Khairusshima
C.H., Che Hassan
A.Ghani, Jaharah
A.K.M., Nurul Amin
Tool wear and surface roughness on milling carbon fiber-reinforced plastic using chilled air
description Carbon fiber-reinforced plastic (CFRP) composite is an expensive material that is widely used in aerospace applications because of its unique properties. During machining, several problems arise because of the carbon in CFRP. Abrasive wear occurs on the cutting tools during CFRP machining, thereby shortening the life of the tools and damaging surface quality. In this study, the performance of the solid carbide end tool and the surface quality of CFRP composite during the milling process were investigated. A cutting speed ranging from 160 m/min to 200 m/min and a feed rate ranging from 0.025 mm/rev to 0.05 mm/rev were used in the experiment. Results show that tool wear is higher at higher feed rates and lower cutting speeds, whereas longer tool life is achieved at lower feed rates and intermediate cutting speeds. Furthermore, a good machined surface is produced at higher cutting speeds and higher feed rates.
format Article
author Muhamad Khairussaleh, Nor Khairusshima
C.H., Che Hassan
A.Ghani, Jaharah
A.K.M., Nurul Amin
author_facet Muhamad Khairussaleh, Nor Khairusshima
C.H., Che Hassan
A.Ghani, Jaharah
A.K.M., Nurul Amin
author_sort Muhamad Khairussaleh, Nor Khairusshima
title Tool wear and surface roughness on milling carbon fiber-reinforced plastic using chilled air
title_short Tool wear and surface roughness on milling carbon fiber-reinforced plastic using chilled air
title_full Tool wear and surface roughness on milling carbon fiber-reinforced plastic using chilled air
title_fullStr Tool wear and surface roughness on milling carbon fiber-reinforced plastic using chilled air
title_full_unstemmed Tool wear and surface roughness on milling carbon fiber-reinforced plastic using chilled air
title_sort tool wear and surface roughness on milling carbon fiber-reinforced plastic using chilled air
publisher Asian Economic and Social Society
publishDate 2012
url http://irep.iium.edu.my/48609/
http://irep.iium.edu.my/48609/
http://irep.iium.edu.my/48609/1/asian_pacific.pdf
first_indexed 2023-09-18T21:08:55Z
last_indexed 2023-09-18T21:08:55Z
_version_ 1777411120306323456

Similar Items