Tool wear and surface roughness on milling carbon fibre reinforced plastic using chilled air

Carbon fibre reinforced plastic (CFRP) composite is one of expensive material which is widely used in aerospace application because of its properties. During machining, several problems arose which are due to the existence of the carbon in CFRP. Abrasive wear can be easily found on the cutting tool...

Full description

Bibliographic Details
Main Authors: Muhamad Khairussaleh, Nor Khairusshima, Che Haron, Che Hassan, A. Ghani, Jaharah, Amin, A. K. M. Nurul
Format: Conference or Workshop Item
Language:English
English
Published: 2012
Subjects:
Online Access:http://irep.iium.edu.my/48603/
http://irep.iium.edu.my/48603/
http://irep.iium.edu.my/48603/1/ID12_FULL_PAPER_EPC__Nor_Khairusshima.pdf
http://irep.iium.edu.my/48603/4/48603.pdf
id iium-48603
recordtype eprints
spelling iium-486032016-07-16T17:52:01Z http://irep.iium.edu.my/48603/ Tool wear and surface roughness on milling carbon fibre reinforced plastic using chilled air Muhamad Khairussaleh, Nor Khairusshima Che Haron, Che Hassan A. Ghani, Jaharah Amin, A. K. M. Nurul T Technology (General) Carbon fibre reinforced plastic (CFRP) composite is one of expensive material which is widely used in aerospace application because of its properties. During machining, several problems arose which are due to the existence of the carbon in CFRP. Abrasive wear can be easily found on the cutting tool during machining CFRP which shorten the life of the tool and damage the surface quality. In this study the performance of solid carbide end tool and surface quality of CFRP composite during milling process was investigated at cutting speed of 160-200 m/min and feed rate of 0.025-0.05 mm/rev. It was found that the tool wear is high at higher feed rate and lower cutting speed. Longer tool life was achieved at lower feed rate and intermediate cutting speed. A good machined surface was produced at higher cutting speed and higher feed rate. 2012 Conference or Workshop Item PeerReviewed application/pdf en http://irep.iium.edu.my/48603/1/ID12_FULL_PAPER_EPC__Nor_Khairusshima.pdf application/pdf en http://irep.iium.edu.my/48603/4/48603.pdf Muhamad Khairussaleh, Nor Khairusshima and Che Haron, Che Hassan and A. Ghani, Jaharah and Amin, A. K. M. Nurul (2012) Tool wear and surface roughness on milling carbon fibre reinforced plastic using chilled air. In: The International Conference on Engineering and Built Environment (ICEBE) 2012, 6th-7th Nov. 2012, Residence Hotel, UNITEN, Bangi, Selangor. (Unpublished) http://www.ukm.my/icebe/index.php/component/content/article/9-pages/117-icebe-2012
repository_type Digital Repository
institution_category Local University
institution International Islamic University Malaysia
building IIUM Repository
collection Online Access
language English
English
topic T Technology (General)
spellingShingle T Technology (General)
Muhamad Khairussaleh, Nor Khairusshima
Che Haron, Che Hassan
A. Ghani, Jaharah
Amin, A. K. M. Nurul
Tool wear and surface roughness on milling carbon fibre reinforced plastic using chilled air
description Carbon fibre reinforced plastic (CFRP) composite is one of expensive material which is widely used in aerospace application because of its properties. During machining, several problems arose which are due to the existence of the carbon in CFRP. Abrasive wear can be easily found on the cutting tool during machining CFRP which shorten the life of the tool and damage the surface quality. In this study the performance of solid carbide end tool and surface quality of CFRP composite during milling process was investigated at cutting speed of 160-200 m/min and feed rate of 0.025-0.05 mm/rev. It was found that the tool wear is high at higher feed rate and lower cutting speed. Longer tool life was achieved at lower feed rate and intermediate cutting speed. A good machined surface was produced at higher cutting speed and higher feed rate.
format Conference or Workshop Item
author Muhamad Khairussaleh, Nor Khairusshima
Che Haron, Che Hassan
A. Ghani, Jaharah
Amin, A. K. M. Nurul
author_facet Muhamad Khairussaleh, Nor Khairusshima
Che Haron, Che Hassan
A. Ghani, Jaharah
Amin, A. K. M. Nurul
author_sort Muhamad Khairussaleh, Nor Khairusshima
title Tool wear and surface roughness on milling carbon fibre reinforced plastic using chilled air
title_short Tool wear and surface roughness on milling carbon fibre reinforced plastic using chilled air
title_full Tool wear and surface roughness on milling carbon fibre reinforced plastic using chilled air
title_fullStr Tool wear and surface roughness on milling carbon fibre reinforced plastic using chilled air
title_full_unstemmed Tool wear and surface roughness on milling carbon fibre reinforced plastic using chilled air
title_sort tool wear and surface roughness on milling carbon fibre reinforced plastic using chilled air
publishDate 2012
url http://irep.iium.edu.my/48603/
http://irep.iium.edu.my/48603/
http://irep.iium.edu.my/48603/1/ID12_FULL_PAPER_EPC__Nor_Khairusshima.pdf
http://irep.iium.edu.my/48603/4/48603.pdf
first_indexed 2023-09-18T21:08:54Z
last_indexed 2023-09-18T21:08:54Z
_version_ 1777411119992799232