Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations
The paper reports the research on the improvement of tool wear resistant of Titanium Carbide (TiC) cutting tool after microwave post sintering treatment. Titanium Carbide square milling insert was microwave sintered at 600°C with 15 minutes of holding time. The face milling operations were conducted...
| Main Authors: | , , , , , |
|---|---|
| Format: | Article |
| Language: | English |
| Published: |
Trans Tech Publications, Switzerland
2015
|
| Subjects: | |
| Online Access: | http://irep.iium.edu.my/44024/ http://irep.iium.edu.my/44024/ http://irep.iium.edu.my/44024/ http://irep.iium.edu.my/44024/1/44024_-_Effect_of_microwave_sintering_treatment_to_the_flank_wear_of_titanium_carbide_tools_in_milling_operations.pdf |
| id |
iium-44024 |
|---|---|
| recordtype |
eprints |
| spelling |
iium-440242018-02-26T10:19:08Z http://irep.iium.edu.my/44024/ Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations Iqbal, Mohammad Ariff, Tasnim Firdaus Mat Roseh, Mohd Shahrul Fahmi Al Hazza, Muataz Hazza Faizi Hilmy, Irfan -, Suryanto T Technology (General) TN600 Metallurgy TS200 Metal manufactures. Metalworking The paper reports the research on the improvement of tool wear resistant of Titanium Carbide (TiC) cutting tool after microwave post sintering treatment. Titanium Carbide square milling insert was microwave sintered at 600°C with 15 minutes of holding time. The face milling operations were conducted to Carbon Steel S45C block (130 mm x 95 mm x 40 mm) by using both of original and microwave sintered insert at 5 different cutting speed (60, 90 , 120 , 150 and 180 m/min), constant feed rate (0.2 mm/tooth) and constant depth of cut (0.2 mm/tooth). The flank wear of the insert was measured every nearest 10th minute of complete cutting passes. The results of the experiment show that microwave post sintering treatment improves the tool resistant of the TiC insert. The flank wear of the sintered insert is lower at any machining time and all cutting speed. The research also found that the percentage of the improvement is lower at higher cutting speed compare to lower cutting speed. Trans Tech Publications, Switzerland 2015-01-20 Article PeerReviewed application/pdf en http://irep.iium.edu.my/44024/1/44024_-_Effect_of_microwave_sintering_treatment_to_the_flank_wear_of_titanium_carbide_tools_in_milling_operations.pdf Iqbal, Mohammad and Ariff, Tasnim Firdaus and Mat Roseh, Mohd Shahrul Fahmi and Al Hazza, Muataz Hazza Faizi and Hilmy, Irfan and -, Suryanto (2015) Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations. Advanced Materials Research, 1115. pp. 59-63. ISSN 1022-6680 http://www.ttp.net/978-3-03835-493-2/2.html 10.4028/www.scientific.net/AMR.1115.59 |
| repository_type |
Digital Repository |
| institution_category |
Local University |
| institution |
International Islamic University Malaysia |
| building |
IIUM Repository |
| collection |
Online Access |
| language |
English |
| topic |
T Technology (General) TN600 Metallurgy TS200 Metal manufactures. Metalworking |
| spellingShingle |
T Technology (General) TN600 Metallurgy TS200 Metal manufactures. Metalworking Iqbal, Mohammad Ariff, Tasnim Firdaus Mat Roseh, Mohd Shahrul Fahmi Al Hazza, Muataz Hazza Faizi Hilmy, Irfan -, Suryanto Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations |
| description |
The paper reports the research on the improvement of tool wear resistant of Titanium Carbide (TiC) cutting tool after microwave post sintering treatment. Titanium Carbide square milling insert was microwave sintered at 600°C with 15 minutes of holding time. The face milling operations were conducted to Carbon Steel S45C block (130 mm x 95 mm x 40 mm) by using both of original and microwave sintered insert at 5 different cutting speed (60, 90 , 120 , 150 and 180 m/min), constant feed rate (0.2 mm/tooth) and constant depth of cut (0.2 mm/tooth). The flank wear of the insert was measured every nearest 10th minute of complete cutting passes. The results of the experiment show that microwave post sintering treatment improves the tool resistant of the TiC insert. The flank wear of the sintered insert is lower at any machining time and all cutting speed. The research also found that the percentage of the improvement is lower at higher cutting speed compare to lower cutting speed. |
| format |
Article |
| author |
Iqbal, Mohammad Ariff, Tasnim Firdaus Mat Roseh, Mohd Shahrul Fahmi Al Hazza, Muataz Hazza Faizi Hilmy, Irfan -, Suryanto |
| author_facet |
Iqbal, Mohammad Ariff, Tasnim Firdaus Mat Roseh, Mohd Shahrul Fahmi Al Hazza, Muataz Hazza Faizi Hilmy, Irfan -, Suryanto |
| author_sort |
Iqbal, Mohammad |
| title |
Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations |
| title_short |
Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations |
| title_full |
Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations |
| title_fullStr |
Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations |
| title_full_unstemmed |
Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations |
| title_sort |
effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations |
| publisher |
Trans Tech Publications, Switzerland |
| publishDate |
2015 |
| url |
http://irep.iium.edu.my/44024/ http://irep.iium.edu.my/44024/ http://irep.iium.edu.my/44024/ http://irep.iium.edu.my/44024/1/44024_-_Effect_of_microwave_sintering_treatment_to_the_flank_wear_of_titanium_carbide_tools_in_milling_operations.pdf |
| first_indexed |
2023-09-18T21:02:37Z |
| last_indexed |
2023-09-18T21:02:37Z |
| _version_ |
1777410724312645632 |