Edge crack, composite materials

Edge crack, composite materials

Bibliographic Details
Main Authors:	Rizk, Abd El-Fattah, Hrairi, Meftah
Format:	Book Chapter
Language:	English
Published:	Springer Reference 2014
Subjects:	TA349 Mechanics of engineering. Applied mechanics
Online Access:	http://irep.iium.edu.my/37130/ http://irep.iium.edu.my/37130/ http://irep.iium.edu.my/37130/ http://irep.iium.edu.my/37130/4/EdgeCrackComposite.pdf

Similar Items

Edge crack, isotropic material
by: Rizk, Abd El-Fattah, et al.
Published: (2014)

Edge Crack, Bimaterial Systems
by: Hrairi, Meftah, et al.
Published: (2014)

Derivation of stress intensity factor for a cracked plate with an integrated piezoelectric actuator
by: Abuzaid, Ahmed, et al.
Published: (2014)

Finite element modeling of clinching process for joining dissimilar materials
by: Eshteyah, Mohanna, et al.
Published: (2015)

Finite element modeling of clinching process for joining dissimilar materials
by: Eshteyah, Mohanna, et al.
Published: (2015)

Transversal crack and delamination of laminates using XFEM
by: Abdullah, Nur Azam, et al.
Published: (2017)

Finite element simulation of electro-mechanical impedance technique
by: Tahmasebpour, Kamyar, et al.
Published: (2015)

Clinching process for joining dissimilar materials: state of the art
by: Eshteyah, Mohanna, et al.
Published: (2016)

Stress analysis of thin-walled laminated composite beams under shear and torsion
by: Syed Mohamed Ali, Jaffar, et al.
Published: (2018)

Machinability study on milling kenaf fiber reinforced plastic composite materials using the design of experiments
by: Harun, Azmi, et al.
Published: (2018)

Multi-objective optimization of clinching joints quality using Grey-based Taguchi method
by: Eshteyah, Mohanna, et al.
Published: (2016)

LEADME : an educational software for composite laminate analysis and design
by: Syed Mohamed Ali, Jaffar, et al.
Published: (2014)

Effect of compaction parameters on the physical properties of zinc oxide varistor discs
by: Karim, A.N. Mustafizul, et al.
Published: (1995)

Morphologies and mechanical properties of polylactic acid / polypropylene carbonate (PLA/PPC) blends by solvent casting method
by: Mohamed Haneef, Intan Najwa Humaira, et al.
Published: (2018)

Two degree of freedom plotter using robotic arm
by: Hanafi, Muhammad Muaz, et al.
Published: (2014)

Prediction of waste heat energy recovery performance in a naturally aspirated engine using artificial neural network
by: Herawan, Safarudin Gazali, et al.
Published: (2014)

Quasi-two-dimensional MHD duct flow around a 180-degree sharp bend in a strong magnetic field
by: Mohammed Sapardi, Mohd Azan, et al.
Published: (2014)

Solder joint reliability assessment: finite element simulation methodology
by: Tamin, M.N., et al.
Published: (2014)

Development and optimization of a low normal force contact
by: Bhuiyan, Moinul, et al.
Published: (2014)

Compensated inverse pid controller for active vibration control with piezoelectric patches: modeling, simulation and implementation
by: Abdul Muthalif, Asan Gani, et al.
Published: (2006)

Introduction of piecewise virtual fields method for solution of inverse problems
by: Syed Muhammad, Kashif
Published: (2011)

Fundamentals of fluid mechanics
by: Faris, Waleed Fekry, et al.
Published: (2009)

Fabrication of microfluidic channel using micro end milling and micro electrical discharge milling
by: Ali, Mohammad Yeakub
Published: (2009)

Experimental Investigation on the Energy Absorption Capability of Foam-filled Nomex Honeycomb Structure
by: Wan Abdul Hamid, Wan Luqman Hakim, et al.
Published: (2013)

Development of educational software for stress analysis of an aircraft wing
by: Mohamed Ali, Jaafar Syed, et al.
Published: (2012)

Design of a gyroscopically stabilized single-wheeled robot
by: Saleh, Tanveer
Published: (2004)

Large displacement optical switching mechanism using SMA microactuator and magnetic latch
by: Bhuiyan, Md. Moinul Islam, et al.
Published: (2004)

LNF Micro-Contact using MEMS and EFF Technology
by: Bhuiyan, Moinul, et al.
Published: (2013)

mathematical modelling and development of a monoball robot for educational purpose
by: M. H., Latif, et al.
Published: (2016)

Comparison of position sensorless control based back-EMF estimators in PMSM
by: Uddin, Md. Nasir, et al.
Published: (2016)

Custom MPPT design of solar power switching network for racing car
by: Uddin, Md. Nasir, et al.
Published: (2015)

Dynamic effects of piezoelectric patch actuators on vibrational response of non-deterministic structures: modelling and simulations
by: Wahid, Azni Nabela, et al.
Published: (2015)

Fatigue fracture process of lead-free solder joints in BGA package
by: Tamin, M.N., et al.
Published: (2012)

Damage mechanics model for solder/intermetallics interface fracture process in solder joints
by: Shaffiar, Norhashimah, et al.
Published: (2011)

3D modeling of austenite based on real microstructure
by: Prawoto, Yunan, et al.
Published: (2012)

Damage progression in BGA solder joints during board-level drop test
by: Yamin, A.F.M., et al.
Published: (2011)

Progressive damage in Sn-4Ag-0.5Cu solder joints during flexural fatigue of a BGA package
by: Shaffiar, Norhashimah, et al.
Published: (2010)

Continuum damage evolution in pb-free solder joint under shear fatigue loadings
by: Shaffiar, Norhashimah, et al.
Published: (2010)

Hygrothermoelastic analysis of anisotropic cylindrical shells
by: Alsubari, Saleh, et al.
Published: (2015)

A higher order theory for bending of cross ply laminated cylindrical shell under hygrothermal loads
by: Syed Mohamed Ali, Jaffar, et al.
Published: (2015)

Cannot write session to /tmp/vufind_sessions/sess_pjnql1r8dp7v5l62kghdhjpe75