Dry machining of brass using titanium carbonitride (TiCN) coated tool

Dry machining is environmentally friendly, clean and safe to be performed. Regardless of decreasing tool life due to lack of lubricants, choosing dry machining over wet machining may be a wiser choice since the cost of purchasing and disposing the cutting fluids can contribute to a higher cost. Wear...

Full description

Bibliographic Details
Main Authors:	Mohamed Ariff, Tasnim Firdaus, Kamarudin, Mohd Syahidan, Haron, Mohd Amiruddin
Format:	Article
Language:	English
Published:	Trans Tech Publications Ltd., Switzerland 2013
Subjects:	T Technology (General) TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/31460/ http://irep.iium.edu.my/31460/ http://irep.iium.edu.my/31460/ http://irep.iium.edu.my/31460/1/ICAMDM_2013_-AMM.372.495-BRASS.pdf

id	iium-31460
recordtype	eprints
spelling	iium-314602013-08-29T02:42:11Z http://irep.iium.edu.my/31460/ Dry machining of brass using titanium carbonitride (TiCN) coated tool Mohamed Ariff, Tasnim Firdaus Kamarudin, Mohd Syahidan Haron, Mohd Amiruddin T Technology (General) TS200 Metal manufactures. Metalworking Dry machining is environmentally friendly, clean and safe to be performed. Regardless of decreasing tool life due to lack of lubricants, choosing dry machining over wet machining may be a wiser choice since the cost of purchasing and disposing the cutting fluids can contribute to a higher cost. Wear rates, tool wear intensities and material removal rates (MRR) of TiCN coated tools using both dry and traditional wet machining on brass were studied with the aim in finding the optimum cutting condition from four different cutting speeds (207, 279, 372 and 498 m/min) with two sets of cutting parameters; depth of cut and feed rate (d = 0.1 mm, f = 0.2 mm/rev and d = 0.2 mm, f = 0.4 mm/rev). Temperatures at the tool-chip interface were measured to analyze the effects of temperature rise during dry machining. Cost analysis on machining cost per piece between dry and wet machining was performed. The optimum cutting condition for wet and dry machining of brass using TiCN coated cutting tool was found to be 498 m/min at d = 0.2 mm, f = 0.4 mm/rev. The tool tip temperature obtained from dry machining did not influence tool wear since the temperature rise is quite similar to the wet machining temperatures. The machining for the dry machining reduced to about 25-76% per piece when compared with wet machining. Trans Tech Publications Ltd., Switzerland 2013-07 Article PeerReviewed application/pdf en http://irep.iium.edu.my/31460/1/ICAMDM_2013_-AMM.372.495-BRASS.pdf Mohamed Ariff, Tasnim Firdaus and Kamarudin, Mohd Syahidan and Haron, Mohd Amiruddin (2013) Dry machining of brass using titanium carbonitride (TiCN) coated tool. Applied Mechanics and Materials, 372. pp. 495-500. ISSN 1660-9336 http://www.scientific.net/AMM.372.495 10.4028/www.scientific.net/AMM.372.495
repository_type	Digital Repository
institution_category	Local University
institution	International Islamic University Malaysia
building	IIUM Repository
collection	Online Access
language	English
topic	T Technology (General) TS200 Metal manufactures. Metalworking
spellingShingle	T Technology (General) TS200 Metal manufactures. Metalworking Mohamed Ariff, Tasnim Firdaus Kamarudin, Mohd Syahidan Haron, Mohd Amiruddin Dry machining of brass using titanium carbonitride (TiCN) coated tool
description	Dry machining is environmentally friendly, clean and safe to be performed. Regardless of decreasing tool life due to lack of lubricants, choosing dry machining over wet machining may be a wiser choice since the cost of purchasing and disposing the cutting fluids can contribute to a higher cost. Wear rates, tool wear intensities and material removal rates (MRR) of TiCN coated tools using both dry and traditional wet machining on brass were studied with the aim in finding the optimum cutting condition from four different cutting speeds (207, 279, 372 and 498 m/min) with two sets of cutting parameters; depth of cut and feed rate (d = 0.1 mm, f = 0.2 mm/rev and d = 0.2 mm, f = 0.4 mm/rev). Temperatures at the tool-chip interface were measured to analyze the effects of temperature rise during dry machining. Cost analysis on machining cost per piece between dry and wet machining was performed. The optimum cutting condition for wet and dry machining of brass using TiCN coated cutting tool was found to be 498 m/min at d = 0.2 mm, f = 0.4 mm/rev. The tool tip temperature obtained from dry machining did not influence tool wear since the temperature rise is quite similar to the wet machining temperatures. The machining for the dry machining reduced to about 25-76% per piece when compared with wet machining.
format	Article
author	Mohamed Ariff, Tasnim Firdaus Kamarudin, Mohd Syahidan Haron, Mohd Amiruddin
author_facet	Mohamed Ariff, Tasnim Firdaus Kamarudin, Mohd Syahidan Haron, Mohd Amiruddin
author_sort	Mohamed Ariff, Tasnim Firdaus
title	Dry machining of brass using titanium carbonitride (TiCN) coated tool
title_short	Dry machining of brass using titanium carbonitride (TiCN) coated tool
title_full	Dry machining of brass using titanium carbonitride (TiCN) coated tool
title_fullStr	Dry machining of brass using titanium carbonitride (TiCN) coated tool
title_full_unstemmed	Dry machining of brass using titanium carbonitride (TiCN) coated tool
title_sort	dry machining of brass using titanium carbonitride (ticn) coated tool
publisher	Trans Tech Publications Ltd., Switzerland
publishDate	2013
url	http://irep.iium.edu.my/31460/ http://irep.iium.edu.my/31460/ http://irep.iium.edu.my/31460/ http://irep.iium.edu.my/31460/1/ICAMDM_2013_-AMM.372.495-BRASS.pdf
first_indexed	2023-09-18T20:45:39Z
last_indexed	2023-09-18T20:45:39Z
_version_	1777409657393905664

Dry machining of brass using titanium carbonitride (TiCN) coated tool

Similar Items