Experimental Investigation of the Effect of Feed Rate and Negative Tool Rake Angle in High Speed Hard Turning
The aim of this paper is to study experimentally the influence of feed rate and negative tool rake angle on surface roughness and flank wear length during high speed hard turning. AISI 4340 was used as work piece material. This steel is hardened to 60 HRC, machined by a mixed ceramic tool (Al₂O₃-...
| Main Authors: | , |
|---|---|
| Format: | Article |
| Language: | English |
| Published: |
Design for Scientific Renaissance
2013
|
| Subjects: | |
| Online Access: | http://irep.iium.edu.my/30261/ http://irep.iium.edu.my/30261/ http://irep.iium.edu.my/30261/1/601-2552-1-PB_%282%29.pdf |
| id |
iium-30261 |
|---|---|
| recordtype |
eprints |
| spelling |
iium-302612013-06-25T07:56:11Z http://irep.iium.edu.my/30261/ Experimental Investigation of the Effect of Feed Rate and Negative Tool Rake Angle in High Speed Hard Turning Al Hazza, Muataz Hazza Faizi Adesta, Erry Yulian Triblas T Technology (General) The aim of this paper is to study experimentally the influence of feed rate and negative tool rake angle on surface roughness and flank wear length during high speed hard turning. AISI 4340 was used as work piece material. This steel is hardened to 60 HRC, machined by a mixed ceramic tool (Al₂O₃- TiC). The experiment was obtained with constant cutting depth (0.15 mm), constant cutting speed (325 m/min), four different feed rates (0.075 – 0.15 mm/rev) and three different tool rake angles (0o, - 6, -12o). The experimental results showed that roughness has an increasing trend with the increasing of the feed rate. In contrast, the roughness has a decreasing trend as the rake angle increases in the negative direction from (0o) to (-12o). The flanks wear length also affected by the feed rate increasing. Finally in order to identify statistically significant trends in the measured parameters and cutting parameters data i.e. feed rate and rake angle, an analysis of variance (ANOVA) was conducted. By using DOE an optimization solution was obtained Design for Scientific Renaissance 2013-03 Article PeerReviewed application/pdf en http://irep.iium.edu.my/30261/1/601-2552-1-PB_%282%29.pdf Al Hazza, Muataz Hazza Faizi and Adesta, Erry Yulian Triblas (2013) Experimental Investigation of the Effect of Feed Rate and Negative Tool Rake Angle in High Speed Hard Turning. Journal of Advanced Science and Engineering Research, 3 (1). pp. 62-69. ISSN 2231-8844 https://www.sign-ific-ance.co.uk/dsr/index.php/JASER/article/view/601/677 |
| repository_type |
Digital Repository |
| institution_category |
Local University |
| institution |
International Islamic University Malaysia |
| building |
IIUM Repository |
| collection |
Online Access |
| language |
English |
| topic |
T Technology (General) |
| spellingShingle |
T Technology (General) Al Hazza, Muataz Hazza Faizi Adesta, Erry Yulian Triblas Experimental Investigation of the Effect of Feed Rate and Negative Tool Rake Angle in High Speed Hard Turning |
| description |
The aim of this paper is to study experimentally the influence of feed rate and negative tool rake angle
on surface roughness and flank wear length during high speed hard turning. AISI 4340 was used as
work piece material. This steel is hardened to 60 HRC, machined by a mixed ceramic tool (Al₂O₃-
TiC). The experiment was obtained with constant cutting depth (0.15 mm), constant cutting speed
(325 m/min), four different feed rates (0.075 – 0.15 mm/rev) and three different tool rake angles (0o, -
6, -12o). The experimental results showed that roughness has an increasing trend with the increasing
of the feed rate. In contrast, the roughness has a decreasing trend as the rake angle increases in the
negative direction from (0o) to (-12o). The flanks wear length also affected by the feed rate increasing.
Finally in order to identify statistically significant trends in the measured parameters and cutting
parameters data i.e. feed rate and rake angle, an analysis of variance (ANOVA) was conducted. By
using DOE an optimization solution was obtained |
| format |
Article |
| author |
Al Hazza, Muataz Hazza Faizi Adesta, Erry Yulian Triblas |
| author_facet |
Al Hazza, Muataz Hazza Faizi Adesta, Erry Yulian Triblas |
| author_sort |
Al Hazza, Muataz Hazza Faizi |
| title |
Experimental Investigation of the Effect of Feed Rate and Negative Tool Rake Angle in High Speed Hard Turning |
| title_short |
Experimental Investigation of the Effect of Feed Rate and Negative Tool Rake Angle in High Speed Hard Turning |
| title_full |
Experimental Investigation of the Effect of Feed Rate and Negative Tool Rake Angle in High Speed Hard Turning |
| title_fullStr |
Experimental Investigation of the Effect of Feed Rate and Negative Tool Rake Angle in High Speed Hard Turning |
| title_full_unstemmed |
Experimental Investigation of the Effect of Feed Rate and Negative Tool Rake Angle in High Speed Hard Turning |
| title_sort |
experimental investigation of the effect of feed rate and negative tool rake angle in high speed hard turning |
| publisher |
Design for Scientific Renaissance |
| publishDate |
2013 |
| url |
http://irep.iium.edu.my/30261/ http://irep.iium.edu.my/30261/ http://irep.iium.edu.my/30261/1/601-2552-1-PB_%282%29.pdf |
| first_indexed |
2023-09-18T20:44:25Z |
| last_indexed |
2023-09-18T20:44:25Z |
| _version_ |
1777409579117707264 |