Kinetic study of reduction roasting of mixed laterite ore and coal

Kinetic study of reduction roasting of mixed laterite ore and coal

Bibliographic Details
Main Authors:	-, Pramusanto, Purwanto, Hadi, Saleh, Nuryadi, Suprianto, Sony
Format:	Book Chapter
Language:	English
Published:	IIUM Press 2011
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/25644/ http://irep.iium.edu.my/25644/ http://irep.iium.edu.my/25644/1/chp12.pdf

Similar Items

Upgrading of laterite ore by reduction and learning
by: Purwanto, Hadi, et al.
Published: (2011)

Upgrading of iron-rich laterite ore using reverse flotation
by: Purwanto, Hadi, et al.
Published: (2011)

Upgrading of iron sand by magnetic concentration and reduction
by: ., Muta'alim, et al.
Published: (2011)

The effect of magnetization on the leached limonitic ore
by: , Pramusanto, et al.
Published: (2009)

Effect of EFB content on reducibility of low grade iron ore composite at 1000°C - 1200°C
by: Purwanto, Hadi, et al.
Published: (2018)

Design and Simulate Mixing of Compressed Natural Gas with Air in a Mixing Device
by: K., Kadirgama, et al.
Published: (2008)

Experimental study on the noise reduction of hydraulic bench
by: Muhammad Saufi, Abdul
Published: (2010)

Enhancement of magnetic properties of Malaysian iron ore by reduction roasting using oil palm empty fruit bunch
by: Purwanto, Hadi, et al.
Published: (2014)

A snake robot with mixed gaits capability
by: Khan, Md. Raisuddin, et al.
Published: (2012)

Turbulence model for axial mixing impeller in unbaffled vessel
by: Mohiuddin, A. K. M., et al.
Published: (2011)

Towards a numerical simulation of supersonic mixing & combustion
by: Kamel, Mohammed, et al.
Published: (2013)

CFD simulation of particle mixing in a fluidized bed
by: Kong, Deyi
Published: (2013)

An improved parameterized controller reduction technique via new frequency weighted model reduction formulation
by: Haja Mohideen, Ahmad Jazlan, et al.
Published: (2017)

Multiobjective Fuzzy Mixed Assembly Line Sequencing Optimization Model
by: Tahriri, Farzad, et al.
Published: (2014)

Introduction to probability safety assessment of nuclear power plant
by: Sutjipto, Agus Geter Edy, et al.
Published: (2011)

A Study of Tyre Cavity Resonance and Noise Reduction using Inner Trim
by: Zamri, Mohamed, et al.
Published: (2015)

A mixed control system for active suspension for off-road vehicles
by: Sabaneh, Omar A. O., et al.
Published: (2016)

Optimization of mixed-model assembly line balancing problem with resource constraints
by: M. M., Razali, et al.
Published: (2017)

Simulation Of Mixed Convective Heat Transfer Using Lattice Boltzmann Method
by: A. R. M., Rosdzimin, et al.
Published: (2010)

Magnetic nanowires (Ni) via chemical reduction method
by: Samykano, Mahendran, et al.
Published: (2018)

Improvement On Particulate Mixing Through Inclined Slotted Swirling Distributor In A Fluidized Bed: An Experimental Study
by: Ahmmad Shukrie, Md Yudin, et al.
Published: (2016)

CFD analysis of SD 7003 airfoil at low reynolds number with a laminar kinetic energy based transition model
by: Islam, Mazharul, et al.
Published: (2017)

Design of a mechanism to mix biogas with air in compression internal combustion engine
by: Ahmad Hazury, Hamid
Published: (2010)

Markov Chain Modelling of Reliability Analysis and Prediction under Mixed Mode Loading
by: Salvinder, Singh, et al.
Published: (2015)

Design and development of noise reduction device for hand drilling machine
by: Wan Hafizee , Wan Zulkiflee
Published: (2012)

Cross gramian based time interval model reduction
by: Haja Mohideen, Ahmad Jazlan, et al.
Published: (2015)

Current research trends on dry, near-dry and powder mixed electrical discharge machining
by: Rahman Khan, Md. Ashikur, et al.
Published: (2011)

Mixing Temperature Measurement of Swirl Cold Flow Exiting Cold Exit of Vortex Tube
by: Mohd Hazwan, Yusof, et al.
Published: (2016)

Investigating drag reduction using turbolence altering pseudo-surface (TAPS)
by: Ashwin Charles, Benedict
Published: (2014)

Effect of reduction roasting by using bio-char derived from empty fruit bunch on the magnetic properties of Malaysian iron ore
by: Purwanto, Hadi, et al.
Published: (2014)

Wrinkling prediction in deep drawing metal forming : kinematic hardening model versus mixed hardening model
by: Wan Iryana, Wan Md Nor
Published: (2017)

Fuzzy Mixed Assembly Line Sequencing and Scheduling Optimization Model Using Multiobjective Dynamic Fuzzy GA
by: Zahari, Taha, et al.
Published: (2014)

Powder mixed micro electro discharge machining (PMμEDM)
by: Ali, Mohammad Yeakub
Published: (2011)

Burr Reduction of Micro-milled Microfluidic Channels Mould Using a Tapered Tool
by: Saptaji, Kushendarsyah, et al.
Published: (2017)

Waste Cooking Oil Blended With The Engine Oil For Reduction of Friction and Wear On Piston Skirt
by: Sakinah, Hisham, et al.
Published: (2017)

Copper (II) Oxide Nanoparticle As Friction Reduction and Anti-Wear Additive In Lubricating Oil
by: H. M., Asnida, et al.
Published: (2016)

Exhaust Emissions Reduction Of Diesel Engine Fueled With Emulsified Palm Oil Methyl Esters
by: Amir, Aziz, et al.
Published: (2014)

Magnetic damping in turning of stainless steel aisi 304 for the reduction of machining vibration and tool wear
by: Amin, A. K. M. Nurul, et al.
Published: (2015)

Attaining simultaneous reduction in nox and smoke by using water-in-biodiesel emulsion fuels for diesel engine
by: Zainal Ambri, Abdul Karim, et al.
Published: (2019)

Improvement of MRR and surface roughness during electrical discharge machining (EDM) using aluminum oxide powder mixed dielectric fluid
by: Khan, Ahsan Ali, et al.
Published: (2018)

Cannot write session to /tmp/vufind_sessions/sess_icos02qhcds1lbjm1mbl91ha8d