Wear mechanism in end milling of Inconel 718

Wear mechanism in end milling of Inconel 718

Nickel-based, creep-resistant, superalloy Inconel 718 is amongst the most difficult alloys to machine. The main reason for the poor machinability of the alloy is the high work-hardening rate by the precipitation of a γ’ phase and the presence of hard abrasive phases such as titanium carbide, niob...

Full description

Bibliographic Details
Main Authors:	Amin, A. K. M. Nurul, Hossain, Ishtiaq, Patwari, Muhammed Anayet Ullah
Format:	Book Chapter
Language:	English
Published:	IIUM Press 2011
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/23611/ http://irep.iium.edu.my/23611/ http://irep.iium.edu.my/23611/4/chp32.pdf

Similar Items

Development of an artificial neural network algorithm for predicting the cutting force in end milling of Inconel 718 alloy
by: Hossain, Ishtiaq, et al.
Published: (2011)

Mathematical model of chip serration frequency in end milling of Inconel 718
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2008)

Artificial neural network algorithm for predicting the surface roughness in end milling of Inconel 718 alloy
by: Hossain, Mohammad Ishtiyaq, et al.
Published: (2011)

Enhancement of machinability of Inconel 718 in end milling through online induction heating of workpiece
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Development of an artificial neural network algorithm for predicting the surface roughness in end milling of inconel 718 alloy
by: Hossain, Mohammad Ishtiyaq, et al.
Published: (2008)

A coupled artificial neural network and RSM model for the prediction of chip serration frequency in end milling of Inconel 718
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2011)

Comparison of machinability of ceramic insert in room temperature and cryogenic cooling conditions during end milling inconel 718
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Prediction of surface roughness in high speed machining of Inconel 718
by: Suhaily, Mokhtar, et al.
Published: (2011)

Enhancement of machinability of nickel based alloy - inconel 718 by induction preheating in end milling using ceramic inserts
by: Mokhtar, Suhaily, et al.
Published: (2010)

Application of response surface methodology coupled with genetic algorithm in the optimization of cutting conditions for surface roughness in end milling of Inconel 718 using coated WC-Co inserts
by: Ishtiyaq, M. H., et al.
Published: (2011)

Enhancement of surface integrity in cryogenic high speed ball nose end milling process of inconel 718
by: Musfirah, Abdul Hadi, et al.
Published: (2020)

Mathematical model for the prediction of chip serration frequency in end milling of steel AISI1020
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2009)

Enhancement of machinability by workpiece preheating in end milling of Ti-6Al-4V
by: Hossain, Muhammad Ishtiyaq, et al.
Published: (2008)

Computational analysis for the prediction chip serration frequency in end milling of steel AISI1020
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2008)

Investigations of the causes of chatter in computer aided manufacturing process during end milling operation
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2008)

Comparison of uncoated and coated carbide inserts in end milling of Ti–6Al–4V in terms of surface roughness
by: Hossain, Mohammad Ishtiaq, et al.
Published: (2008)

Chip serration frequency-the primary cause of chatter during end milling operation
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2011)

Identification of instabilities of the chip formation and it’s prediction model during end milling of medium carbon steel (S45C)
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2010)

A new technique to improve the machinability of hardened steel AISI H13 in end milling
by: Amin, A. K. M. Nurul, et al.
Published: (2010)

Prediction and investigation of surface response in high speed end milling of Ti-6Al-4V and optimization by genetic algorithm
by: Alam, Md. Shah, et al.
Published: (2010)

Preheated machining in end milling of hardened steel AISI D2
by: Lajis, M. A., et al.
Published: (2008)

A statistical approach for the prediction of cutting forces in end milling of medium carbon steel (S45C)
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2008)

Prediction model of cutting force by cutting parameters using response surface methodology in end milling of steel AISI 1020
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2008)

Machinability improvement by workpiece preheating during end milling AISI H13 hardened steel
by: Mokhtar, Suhaily, et al.
Published: (2011)

A new technique for the investigation of chatter formation during end milling of medium carbon steel (AISI 45)
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2010)

Tool wear and surface roughness aspects in heat assisted end milling of AISI D2 hardened steel
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Study on wear mechanism of solid carbide cutting tool in milling CFRP
by: Muhamad Khairussaleh, Nor Khairusshima, et al.
Published: (2016)

Modes and progression of tool deterioration and their effects on cutting force during end milling of 718plus Ni-based superalloy using cemented WC-Co tools
by: Nurul Hidayah, Razak
Published: (2017)

Resonance effect in chatter formation in metal cutting
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Study of wear mechanism in the contact between table liner and roller of vertical roller mills
by: Kamal, Ariffin
Published: (2011)

The method of chatter suppression in end milling operation
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Prediction Modeling of Torque in End-milling
by: K., Kadirgama, et al.
Published: (2010)

A novel method for chatter control and improvement of surface finish in end milling
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Finite element and experimental analysis of dynamic behaviour of Vertical Machining Centre Components by Modal Analysis
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2009)

PCD inserts in end milling of Aluminum Silicon Carbide (AlSiC)
by: M. K. , Nor Khairusshima, et al.
Published: (2011)

Prediction Modelling Of Power And Torque In End-Milling
by: K., Kadirgama, et al.
Published: (2009)

Investigation of the machinability of Inconel 718 in room temperature and preheated conditions
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Application of permanent electromagnet for chatter control in end milling of medium carbon steel
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Vibration issue in micro end milling
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Fourth Order Torque Prediction Model in End Milling
by: K., Kadirgama, et al.
Published: (2009)

Cannot write session to /tmp/vufind_sessions/sess_ddfjlmran2j25avpto7tfqjrdf