A coupled artificial neural network and RSM model for the prediction of chip serration frequency in end milling of Inconel 718
Serious vibrations are often encountered due to chip segmentation that limits material removal rates. Different types of chips are formed during machining. The nature of chip formation process is extremely complicated. Chip formation process has a discrete nature, associated with the periodic she...
| Main Authors: | , , |
|---|---|
| Format: | Book Chapter |
| Language: | English |
| Published: |
IIUM Press
2011
|
| Subjects: | |
| Online Access: | http://irep.iium.edu.my/23594/ http://irep.iium.edu.my/23594/ http://irep.iium.edu.my/23594/4/chp15.pdf |
| Summary: | Serious vibrations are often encountered due to chip segmentation that limits material
removal rates. Different types of chips are formed during machining. The nature of chip
formation process is extremely complicated. Chip formation process has a discrete nature,
associated with the periodic shearing process of the chip during machining of Inconel 718.
The instabilities of chip formation process are expressed in terms of primary or secondary
serrated frequency. In order to increase productivity, tool life and chatter suppression in the
machining of Inconel 718, it is necessary to study the chip segmentation phenomena and its
influencing factors.
Chips are formed during the machining of work-pieces. The side of the chip in contact with
the cutting tool is normally shiny, flat and smooth while the other side, which is the free
work-piece surface, is jagged due to shear. It is important to study the formation of chips
during the machining process as the former affects the surface finish, cutting forces,
temperature, tool life, dimensional tolerance and chatter. Understanding the chip formation
during the machining process for the specific materials will allow us to determine the
machining speeds, feed rates and depth of cuts for efficient machining and increased tool life
in the specific actual machining operation as well as chatter free machining. In metal cutting,
the present tendency is towards achieving increased material removal rates with very reliable
machining processes, where the predictability of surface finish, work-piece accuracy, chatter
and tool life are of prime importance. But to maintain stable machining, much attention must
also be paid to the formation of the desired type of chip and chip controls to facilitate its easy
removal. One of the restrictions limiting large material removal rates is the tendency of the
machine tool to chatter. Trent, Talantov, Amin and others [1-3] considered the formation of
chips with serrated teeth to be the primary cause of chatter. They found that chatter arising
during turning is a result of resonance, caused by mutual interaction of the vibrations due to
serrated elements of the chip and the natural vibrations of the system components, e.g. the
spindle and the tool holder [2-3]. Komanduri [4-5] has made some remarkable progress in
the research of chip segmentation and instability in chip formation. Nevertheless it appears
that very few works have been done to investigate the nature of chip formation in end milling because of its complexity and geometrical difficulty. Amin [6] earlier established that the
instability of chip formation could be lowered by preheating the work material during
turning. Yuan Ning et al. [7] indicates that chatter could be reliably recognized by analysis of
the chips. Ekinoviˆc et.al [8] mentioned in their work that cutting speed has significant effect
on chip formation models. Similar influence of the cutting speed on the chip structure and
chip compression ratio was revealed in the experiments conducted by Tonshoff et al. [9]. As
the chip formation process appears to be cyclic, its frequency is of interest. The frequency of
chip formation can be measured by calculating the number of teeth produced in unit time as
proposed by Talantov [10]. But it is very important to investigate the effect of cutting
parameters on the chip serration frequency considering nonlinearity and time variant.
Compared to traditional computing methods, the artificial neural networks (ANNs) are robust
and global. ANNs have the characteristics of universal approximation, parallel distributed
processing, hardware implementation, learning and adaptation, and multivariable systems
[11]. However, this study was inspired by the very limited work on the application of ANNs
in modeling the relationship between cutting conditions and the chip serration frequency
during high-speed end milling of Inconel 718. |
|---|