Design of a simple and affordable electric bicycle

Design of a simple and affordable electric bicycle

Bibliographic Details
Main Authors:	Mohamed Ariff, Tasnim Firdaus, Ewing, Goey, Kam , Yee Wah
Format:	Book Chapter
Language:	English
Published:	IIUM Press 2011
Subjects:	TA401 Materials of engineering and construction
Online Access:	http://irep.iium.edu.my/21322/ http://irep.iium.edu.my/21322/ http://irep.iium.edu.my/21322/1/1.pdf

Similar Items

Design of bicycle helmet using FEA
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2011)

Mould design for handphone casing using moldflow
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2011)

Application of statistical quality control for quality improvement
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2011)

Study of TiC cutting tool insert using microwave synthesis
by: Thauri, Shahdura Hammad, et al.
Published: (2011)

Resistive switching of Cu/Cu2O junction fabricated using simple thermal oxidation at 423 K for memristor application
by: Ani, Mohd Hanafi, et al.
Published: (2018)

Electrical characterisation of highly doped triangular silicon nanowires
by: Za'bah, Nor Farahidah, et al.
Published: (2014)

Effect of Numbers of Fringing Electric Field (FEF) Fingers on the Performance of Sensor for Water Content in Soil
by: Azman, Mohd Farizul, et al.
Published: (2013)

Design for manufacture: towards improved manufacturability
Published: (2011)

Design and fabrication of industrial welding robotic arm
by: Syed Abdullah, Syed Idros, et al.
Published: (2011)

Improvement of typical hip-joint design for gripping and fixing
by: Mohamad Badari, Siti Norbahiyah, et al.
Published: (2011)

Design and performance analysis of VCO for standard GSM using MEMS
by: Al-Khateeb, Khalid A. Saeed, et al.
Published: (2010)

Materials selection and design
by: Maleque, Md. Abdul, et al.
Published: (2013)

Electrical properties dependence on substrate temperature of sputtered ZnO nanoparticles thin films on teflon substrates
by: Nur Sa’adah, Muhamad Sauki, et al.
Published: (2013)

Irradiation modification of epoxidized natural rubber/ethylene vinyl acetate/carbon nanotubes nanocomposites
by: Mohamed Yatim, Norazlina, et al.
Published: (2012)

Experimental study of the influence of ply orientation on DCB mode-I delamination behavior by using multidirectional fully isotropic carbon/epoxy laminates
by: Mohamed Rehan, Muhammad Saifuddin, et al.
Published: (2017)

Analysis by means of surface response to chemical composition and pozzolanic reactivity of Ultrafine Treated Rice Husk Ash (UFTRHA) as cementing additive material
by: Saad, Siti Asmahani, et al.
Published: (2018)

Evaluation of the effects of copper electroplating parameters on the adhesion using response surface methodology
by: Mohamed Haider, Farag I., et al.
Published: (2017)

Fabrication of flexible Au/ZnO/ITO/PET memristor using dilute electrodeposition method
by: Fauzi, Fatin Bazilah, et al.
Published: (2015)

Transition metal oxide (TMO) thin film memristor on cu substrate using dilute electrodeposition method
by: Fauzi, Fatin Bazilah, et al.
Published: (2015)

A critical review on the contributions of chemical and physical factors toward the nucleation and growth of large-area graphene
by: Ani, Mohd Hanafi, et al.
Published: (2018)

Observation on void formed in oxide scale of Fe-Cr-Ni alloy at 1073K in dry and humid environments
by: Akhbar, Kaderi, et al.
Published: (2011)

Dependence of the fracture toughness on the sintering time of dense hydroxyapatite bioceramics
by: Tolouei, Ranna, et al.
Published: (2011)

Chemical resistance tests on PP-ternary nanocomposite for its application in bioreactor liner fabrication
by: Yusof, Faridah, et al.
Published: (2011)

Effect of hydroxyapatite and tricalcium phosphate addition on protein foaming-consolidation porous alumina
by: Sopyan, Iis, et al.
Published: (2011)

Properties of compression moulding starch-nanoclay biocomposites
by: Ahmad, Zuraida, et al.
Published: (2011)

A surgical training model manufacture using fused deposition modeling
by: Mohamad Ali, Hasanudin Hafis, et al.
Published: (2011)

Reverse engineering for rapid prototyping of automotive components
by: Wan Yusoff, Wan Ahmad Yusmawiza, et al.
Published: (2011)

The development of cost estimation for quality assurance system in die-casting processes
by: A Hamzah, Nur Hanisah, et al.
Published: (2011)

Study the adherence of the values in the ISO 9001:2000 certified companies in Malaysia
by: Che Daud, Mohd Radzi, et al.
Published: (2011)

Cost comparison analysis between strip to coil for support brake pedal at Suria Component (M) Sdn. Bhd
by: Che Daud, Mohd Radzi, et al.
Published: (2011)

Performance measurement of SMEs manufacturing sector in Malaysia
by: Wan Yusoff, Wan Ahmad Yusmawiza, et al.
Published: (2011)

The introduction of fit manufacturing as a performance measuring approach towards sustainability of selected manufacturing companies in Malaysia
by: Wan Yusoff, Wan Ahmad Yusmawiza, et al.
Published: (2011)

Implementation of FMECA on Fixed Assembly Cell (FAC)
by: Wan Yusoff, Wan Ahmad Yusmawiza, et al.
Published: (2011)

Fabrication of metal matrix composite automotive brake rotor: part 1
by: Maleque, Md. Abdul
Published: (2011)

Fabrication of metal matrix composite automotive brake rotor: part 2
by: Maleque, Md. Abdul
Published: (2011)

Wear of aluminium matrix composite – effects of reinforcement combination
by: Maleque, Md. Abdul, et al.
Published: (2011)

Mechanical properties of wood plastic composites
by: Ooi, Chong Jin, et al.
Published: (2011)

Properties of wood fiber reinforced polypropylene composite
by: Mridha, Shahjahan, et al.
Published: (2011)

The effects of chemical and mechanical treatments on coir fiber to mechanical properties of coir-albumen-concrete
by: Ahmad, Zuraida, et al.
Published: (2011)

Architecture of chopped fiber glass in plastic composite processed under different loads
by: Md Idriss, Ahmed Nazrin, et al.
Published: (2011)

Cannot write session to /tmp/vufind_sessions/sess_prf8shj1168pf4mv814m76ppc5