Modeling of compression systems

Modeling of compression systems

Bibliographic Details
Main Author:	Idres, Moumen
Format:	Book Chapter
Language:	English
Published:	IIUM Press 2011
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/21075/ http://irep.iium.edu.my/21075/ http://irep.iium.edu.my/21075/1/Chapter_5.pdf

Similar Items

Compressor models
by: Idres, Moumen
Published: (2011)

Introduction to compressors
by: Idres, Moumen
Published: (2011)

Three-dimensional analysis of compressors
by: Idres, Moumen
Published: (2011)

Rotating stall and surge
by: Idres, Moumen
Published: (2011)

Air supply system transient model for proton exchange membrane fuel cell
by: Mohammed Idres, Moumen, et al.
Published: (2011)

Dynamic thermal model for proton-exchange membrane fuel cell
by: Mohamed Idres, Moumen, et al.
Published: (2010)

Constrained model predictive control for proton exchange membrane fuel cell
by: Abdullah, Muhammad Faris, et al.
Published: (2014)

Air supply system transient model for proton exchange membrane fuel cell
by: Mahmoud Idres, Moumen Mohammed, et al.
Published: (2011)

Fuel cell starvation control using model Predictive technique with laguerre and exponential weight functions
by: Abdullah, Muhammad Faris, et al.
Published: (2014)

Development of compressed air powered engine system based on subaru ea71 model
by: Chen, Rui
Published: (2013)

Design and development of a compressed air machine using a compressed air energy storage system
by: Abdul Aziz, M., et al.
Published: (2015)

Surge and rotating stall
by: Idres, Moumen
Published: (2011)

Evaluation of Orifice Flow Meter Accuracy under Pulsation Conditions
by: Abdullah, mohammad, et al.
Published: (2015)

Effect of Compression Ratio on Compression Ignition Engine Performance Operating with Biofuel
by: Akasyah, M Khathri, et al.
Published: (2014)

Study on The Effective Parameter of Gas Turbine Model with Intercooled Compression Process
by: Thamir K., Ibrahim, et al.
Published: (2010)

Speech coding using compressive sensing on a multicore system
by: Gunawan, Teddy Surya, et al.
Published: (2011)

A Review of Compressed-air Hybrid Technology in Vehicle System
by: F., Wasbari, et al.
Published: (2017)

The best compression ratio of modified piston for compressed natural gas(CNG)usage
by: Izar Farhan, Nor Khiri
Published: (2009)

Homogeneous Charge Compression Ignition Combustion: Advantages Over Compression Ignition Combustion, Challenges and Solutions
by: M. M., Hasan, et al.
Published: (2016)

Numerical Modeling on Homogeneous Charge Compression Ignition Combustion Engine Fueled by Diesel-Ethanol Blends
by: H., Hanafi, et al.
Published: (2016)

Development of economical vehicle model for pedestrian-friendly front-end profile study
by: Kausalyah, Venkatason, et al.
Published: (2014)

Particle swarm optimization of micro air launch vehicle trajectory
by: Omar, Hanafy, et al.
Published: (2011)

One-dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-based thermoelectrically controlled micronozzle
by: Hameed, Ammar, et al.
Published: (2012)

Particle Swarm-Based Micro Air Launch Vehicle Trajectory Optimization Method
by: Omar, Hanafy, et al.
Published: (2012)

Development and optimization of a vehicle front-end geometry model for improved pedestrian safety
by: Abdullah, Kassim Abdulrahman, et al.
Published: (2014)

Cylindrical shell buckling under axial compression load
by: Shah, Qasim Hussain, et al.
Published: (2011)

Energy Separation Mechanism in Unconfined Laminar Compressible Vortex
by: Katanoda, Hiroshi, et al.
Published: (2015)

Characterization Of The Response Of Synthetic Bone Substitute To Compressive Load
by: Zamzuri, Hamedon, et al.
Published: (2009)

One dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-Based thermoelectrically controlled micronozzle
by: Mohammed Idres, Moumen, et al.
Published: (2011)

Effectiveness of wheel-typed grain design for hybrid rocket motor performance
by: Kafafy, Raed Ismail, et al.
Published: (2013)

Simulation of wheel type fuel grain in hybrid rocket motor
by: Azami, Muhammad Hanafi, et al.
Published: (2013)

Hybrid rocket performance with varying additive concentrations
by: Kafafy, Raed, et al.
Published: (2013)

Experimental and numerical simulation of hollow structure under compression loading
by: Abdullah, Kassim Abdulrahman, et al.
Published: (2012)

Performance of Compressed Natural Gas (CNG) Engine with Pre Chamber
by: M. S., Ali, et al.
Published: (2016)

Development of compress air transportation (CAT) for alternative energy utilization
by: Mohd Dzulqarnain, Ahmad Suhaimi
Published: (2007)

Effect of Compression Ratio on the Performance of Different Strategies for the Gas Turbine
by: Ibrahim, T. K., et al.
Published: (2014)

Investigation of energy absorption capabilities of compressed and uncompressed crushable foams
by: Shah, Qasim Hussain, et al.
Published: (2015)

Monte Carlo analysis of the human vertebra based on compressive loading
by: Zulkifli, Ahmad@Manap, et al.
Published: (2012)

Effect of the Compression Ratio on the Performance of Different Strategies of the Gas Turbine
by: M. M., Rahman, et al.
Published: (2014)

Scaling Effects for Compression Loaded of Corrugated-core Sandwich Panels
by: M. R. M., Rejab, et al.
Published: (2016)

Cannot write session to /tmp/vufind_sessions/sess_lt5bnltl8r4i7nrjbivj1m782r