Introduction to compressors

Introduction to compressors

Bibliographic Details
Main Author:	Idres, Moumen
Format:	Book Chapter
Language:	English
Published:	IIUM Press 2011
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/21069/ http://irep.iium.edu.my/21069/ http://irep.iium.edu.my/21069/1/Chapter_1.pdf

Similar Items

Compressor models
by: Idres, Moumen
Published: (2011)

Three-dimensional analysis of compressors
by: Idres, Moumen
Published: (2011)

Novel Lubricant Compressor For Automotive Air Conditioning System
by: Azmi, W. H.
Published: (2017)

Aerodynamic Studies in the Static Components of a Centrifugal Compressor Stage
by: Reddy, K. Srinivasa, et al.
Published: (2011)

Design And Development Of A Single Vane Rotating Sleeve Rotary Compressor For Refrigeration System
by: Mohd Yusof, Taib
Published: (2010)

Two-dimensional analysis of compressors
by: Idres, Moumen
Published: (2011)

Rotating stall and surge
by: Idres, Moumen
Published: (2011)

Modeling of compression systems
by: Idres, Moumen
Published: (2011)

Surge and rotating stall
by: Idres, Moumen
Published: (2011)

Evaluation of Orifice Flow Meter Accuracy under Pulsation Conditions
by: Abdullah, mohammad, et al.
Published: (2015)

Dynamic thermal model for proton-exchange membrane fuel cell
by: Mohamed Idres, Moumen, et al.
Published: (2010)

Constrained model predictive control for proton exchange membrane fuel cell
by: Abdullah, Muhammad Faris, et al.
Published: (2014)

Fuel cell starvation control using model Predictive technique with laguerre and exponential weight functions
by: Abdullah, Muhammad Faris, et al.
Published: (2014)

Particle swarm optimization of micro air launch vehicle trajectory
by: Omar, Hanafy, et al.
Published: (2011)

One-dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-based thermoelectrically controlled micronozzle
by: Hameed, Ammar, et al.
Published: (2012)

Particle Swarm-Based Micro Air Launch Vehicle Trajectory Optimization Method
by: Omar, Hanafy, et al.
Published: (2012)

One dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-Based thermoelectrically controlled micronozzle
by: Mohammed Idres, Moumen, et al.
Published: (2011)

Effectiveness of wheel-typed grain design for hybrid rocket motor performance
by: Kafafy, Raed Ismail, et al.
Published: (2013)

Simulation of wheel type fuel grain in hybrid rocket motor
by: Azami, Muhammad Hanafi, et al.
Published: (2013)

Hybrid rocket performance with varying additive concentrations
by: Kafafy, Raed, et al.
Published: (2013)

Particle swarm optimization of air-launch vehicle and trajectory
by: Aldheeb, M, et al.
Published: (2011)

On the scaling of air launch vehicles
by: Kafafy, Raed, et al.
Published: (2011)

Air supply system transient model for proton exchange membrane fuel cell
by: Mohammed Idres, Moumen, et al.
Published: (2011)

Numerical simulation and validation of high-speed turbulent and chemically-reacting flows
by: Kamel, Mohammed, et al.
Published: (2015)

Numerical simulation of supersonic and turbulent combustion with trans-verse sonic fuel injection
by: Kamel, Mohammed, et al.
Published: (2015)

Effect of varying design options on the transient behavior of a hybrid rocket motor
by: Kafafy, Raed Ismail, et al.
Published: (2014)

Towards a numerical simulation of supersonic mixing & combustion
by: Kamel, Mohammed, et al.
Published: (2013)

Air supply system transient model for proton exchange membrane fuel cell
by: Mahmoud Idres, Moumen Mohammed, et al.
Published: (2011)

Two-dimensional flow properties of micronozzle under varied isothermal wall conditions
by: Hameed, Amar Hasan, et al.
Published: (2011)

Frequency estimation of flow induced vibration in thin cantilever plate
by: Javeed, Abdulhakeem, et al.
Published: (2013)

Experimental investigation of the performance of flutter-based microgenerators
by: Kafafy, Raed, et al.
Published: (2013)

Performance analysis of a small capacity horizontal axis wind turbine using QBlade
by: Ali, Said, et al.
Published: (2019)

Design optimization of Micro Air Launch Vehicle using differential evolution
by: Aldheeb, Mohammed, et al.
Published: (2012)

Design, fabrication and flight testing of a surveillance UAV
by: Idres, Moumen, et al.
Published: (2015)

Three-dimensional vibration analysis of fluid-filled pipes
by: Kolo, Isa, et al.
Published: (2013)

Development of generic algorithm in wheel-typed hybrid rocket grain design for performance estimation
by: Kafafy, Raed, et al.
Published: (2012)

Introduction to machine element design for engineers
by: Faris, Waleed Fekry
Published: (2011)

Investigation of Malaysian low earth orbits for remote sensing applications
by: Okasha, Mohamed Elsayed Aly Abd Elaziz, et al.
Published: (2017)

Orifice plate flowmeter performance under pulsating flow conditions
by: Idres, Moumen, et al.
Published: (2014)

Development of economical vehicle model for pedestrian-friendly front-end profile study
by: Kausalyah, Venkatason, et al.
Published: (2014)

Cannot write session to /tmp/vufind_sessions/sess_45qo5romh81pi3ap8tl56oe4cj