Review of Malaysian traffic summon and payment system

Review of Malaysian traffic summon and payment system

Bibliographic Details
Main Authors:	Aibinu, Abiodun Musa, Syed Mohammad, Sharifah Nadiah, Wan Azmi, Wan Nur Faezah
Format:	Book Chapter
Language:	English
Published:	IIUM Press 2011
Subjects:	TJ170 Mechanics applied to machinery. Dynamics
Online Access:	http://irep.iium.edu.my/20211/ http://irep.iium.edu.my/20211/ http://irep.iium.edu.my/20211/4/Chp46.pdf

Similar Items

Development of palmprint based biometric system
by: Rotinwa-Akinbile, M. A., et al.
Published: (2011)

Hot Water Rocket System (HWRS) - preliminary design and prototype development of a pressurized how water casing (PHWC)
by: Kashif, Syed Muhammad
Published: (2012)

Monitoring of fatigue damage using ultrasonics and finite element analysis
by: Hrairi, Meftah, et al.
Published: (2012)

Load carrying capability of liquid filled cylindrical shell structures under axial compression
by: Hussain Shah, Qasim, et al.
Published: (2011)

Biodiesel production process optimization from spirulina maxima microalgae and performance investigation in a diesel engine
by: Rahman, Md Atiqur, et al.
Published: (2017)

Numerical investigation of flow boiling in double-layer microchannel heat sink
by: Ahmed, Shugata, et al.
Published: (2014)

An evaluation of LQR and fuzzy logic controllers for active suspension using half car model
by: Hasbullah, Faried, et al.
Published: (2010)

A study of noise transmission through cylindrical shell using modal truncation approach
by: El-Hafidi, Ali, et al.
Published: (2011)

Dynamic characterisation of elastomeric engine mounts of different geometry used in automotive industry: simulation approach
by: Faris, Waleed Fekry, et al.
Published: (2010)

Active engine mounting controller using extended minimal resource allocating networks
by: Darsivan, Fadly Jashi, et al.
Published: (2008)

Investigation into noise problems in vehicle structure using vibro-acoustic approach
by: Hanouf, Zahir Ahmad, et al.
Published: (2009)

Aerodynamic derivatives identification for ground vehicles in crosswind using neural network and PCA
by: Ramli, Nabilah, et al.
Published: (2010)

Experimental and numerical study on the orthogonal and oblique impact on water filled pipes
by: Hussain Shah, Qasim
Published: (2011)

Effect of tapered angle of a conical nose indenter on the energy absorbing variation of a copper pipe subjected to axial crushing
by: Shah, Qasim Hussain, et al.
Published: (2012)

A comparison of energy absorbing capabilities of paper and steel structures subjected to progressive failure under free falling objects
by: Shah, Qasim Hussain, et al.
Published: (2007)

Finite element modelling of damage fracture and fretting fatigue
by: Wahab, M. Abdel, et al.
Published: (2012)

Analysis of thermal stress intensity factors for edge cracked bimaterial system
by: Hrairi, Meftah, et al.
Published: (2012)

Kernel PCA – an introduction
by: Baali, Hamza, et al.
Published: (2011)

System modelling of a twin rotor system: time and frequency domain analysis
by: Toha, Siti Fauziah, et al.
Published: (2011)

LS-DYNA for beginners: an insight into Ls-Prepost and Ls-Dyna
by: Hussain Shah, Qasim, et al.
Published: (2012)

Evaluation of friction welded bi-material joint strength subjected to impact loads
by: Shah, Qasim Hussain, et al.
Published: (2011)

Dynamics and control policies analysis of semi-active suspension systems using a full-car model
by: Ihsan, Sany Izan, et al.
Published: (2007)

Development of vibration suppression devices from smart fluids
by: Rashid, Muhammad Mahbubur, et al.
Published: (2011)

Development of fuzzy logic controller for magnetorheological rotary brake system
by: Rashid, Muhammad Mahbubur, et al.
Published: (2009)

The damage of unconfined granite edge due to the impact of varying stiffness projectiles
by: Shah, Qasim Hussain, et al.
Published: (2013)

Modal analysis of car panels using finite element analysis
by: Hanouf, Zahir
Published: (2011)

Performance and cost analysis of diesel engine with different mixing ratio of raw vegetable oil and diesel fuel
by: Uddin, Md. Nasir, et al.
Published: (2016)

Implementation of lean manufacturing to blend with good manufacturing practice at Minda Tulus Industries Sdn. Bhd. for improved performance
by: Nasry, Nasrul Ashraf, et al.
Published: (2017)

Image-based feature extraction technique for inclined crack quantification using pulsed eddy current
by: Nafiah, Faris, et al.
Published: (2019)

Development of design structure matrix of product architecture case study: multi purpose CNC router
by: Hilmy, Irfan, et al.
Published: (2014)

Control of suddenly expanded flow for area ratio 3.61
by: Syed, Syed Ashfaq, et al.
Published: (2013)

Finite element and experimental analysis of dynamic behaviour of Vertical Machining Centre Components by Modal Analysis
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2009)

System identification technique for a helicopter using genetic algorithms
by: Toha, Siti Fauziah, et al.
Published: (2011)

Effect of cryogenic cooling on the micro structure and properties of ferritic stainless steel welds
by: Mridha, Shahjahan
Published: (2012)

Enhancement of thermal conductivity and kinematic viscosity in magnetically controllable maghemite (γ-Fe2O3) nanofluids
by: Nurdin, Irwan, et al.
Published: (2016)

Synchronization and antisynchronization protocol design of chaotic nonlinear gyros: an adaptive integral sliding mode approach
by: Rehman, Fazal ur, et al.
Published: (2019)

Influence of internal fill pattern, polishing time and Z-Axis orientation on the tensile strength of the 3D printed part
by: Seprianto, Dicky, et al.
Published: (2019)

In-socket sensory system with an adaptive neuro-based fuzzy inference system for active transfemoral prosthetic legs
by: Mohd Yusof, Nur Hidayah, et al.
Published: (2019)

High aspect ratio micro-EDM drilling with nano surface finish
by: Ali , Mohammad Yeakub, et al.
Published: (2016)

Evaluation of fatigue damage in adhesive bonding: Part 1: Bulk adhesive
by: Wahab, Magd Abdel, et al.
Published: (2010)