Production of aluminium reinforced with SiC particulates using powder metallurgy

Production of aluminium reinforced with SiC particulates using powder metallurgy

Bibliographic Details
Main Author:	Nimir, Yassin Lutfi Mahmud
Format:	Book Chapter
Language:	English
Published:	IIUM Press 2011
Subjects:	TJ Mechanical engineering and machinery TL Motor vehicles. Aeronautics. Astronautics
Online Access:	http://irep.iium.edu.my/19667/ http://irep.iium.edu.my/19667/ http://irep.iium.edu.my/19667/1/Chapter_24.pdf

Similar Items

Wear behavior of as-cast and heat treated triple particle size SiC reinforced aluminium metal matrix composites
by: Maleque, Md. Abdul, et al.
Published: (2009)

Analysis of reduction of particulate matter concentration and size distribution of di diesel engine by seawater spray
by: Pramnath, Ravi
Published: (2012)

Analysis of diesel particulate matter on single cylinder diesel engine using waste plastic fuel
by: Mohd Radzi, Mohd Rasol
Published: (2012)

Design and development of 1-seated urban car chassis using aluminium
by: Fazliana, Fauzun
Published: (2010)

Computational crashworthy optimization of partially filled aluminium foam for automative side member
by: Salwani, Mohd Salleh
Published: (2013)

Design and development of integrated chassis of one seated urban car using embedded aluminium and FRP
by: Noor Akmal, Zolkifli
Published: (2010)

Investigation of 1-dimensional analysis for two-stroke spark ignition (SI) engine
by: Zabidi , Mohamad
Published: (2008)

Spring-back of thick uni-directional carbon fibre reinforced composite laminate for aircraft structure application
by: Zakaria, Mohd Hafizu, et al.
Published: (2018)

Heat transfer performance of Ti02- Si02 nanofluid in water-ethylene glycol mixture
by: M. F., Nabil, et al.
Published: (2017)

Production of aluminum-silicon carbide composites using powder metallurgy at sintering temperatures above the aluminum melting point part II
by: Nimir, Yassin Lutfi Mahmud
Published: (2011)

Vibration isolation analysis of new design OEM damper for malaysia vehicle suspension system featuring MR fluid
by: Unuh., M. H., et al.
Published: (2018)

Improvement of front car bumper system
by: Muhamad Firdaus, Mahmud
Published: (2008)

Satellite attitude tracking control using Lyapunov control theory
by: Okasha, Mohamed Elsayed Aly Abd Elaziz, et al.
Published: (2019)

Evaporative cooling system for electric vehicles battery pack
by: Khalid, A. Hilmi, et al.
Published: (2013)

Peminangan atau melamar, dan akibatnya menurut hukum Islam serta undang-undang Islam di Indonesia
by: Awang, Abdul Bari, et al.
Published: (2018)

Control of suddenly expanded flows from correctly expanded and under expanded nozzles at supersonic mach number for area ratio 2.56
by: Bashir, Musavir, et al.
Published: (2016)

Passive control of base drag in compressible subsonic flow using multiple cavity
by: Khan, Sher Afghan, et al.
Published: (2018)

Auto-City Theme Park, Juru, Penang
by: Razali, Syazleen, et al.
Published: (2019)

Ride comfort performance of a vehicle using active suspension system with active disturbance rejection control
by: Faried Hasbullah, Faried Hasbullah, et al.
Published: (2015)

Experimental studies on low speed converging nozzle flow with sudden expansion
by: Ashfaq, Syed, et al.
Published: (2014)

Studies on suddenly expanded flow at different levels of over expansion for area ratio 3.24
by: Baig, Maugal Ahmed Ali, et al.
Published: (2012)

Wall pressure studies in a suddenly expanded flow for area ratio 2.56”
by: Baig, Maugal Ahmed Ali, et al.
Published: (2012)

High incidence supersonic similitude for planar wedge
by: Crasta, Asha, et al.
Published: (2012)

Estimation of stability derivatives of a delta wing in hypersonic flow
by: Crasta, Asha, et al.
Published: (2012)

Oscillating supersonic delta wings with straight leading edges
by: Crasta, Asha, et al.
Published: (2012)

Effect on base pressure in suddenly expanded flows with variable location of microjets
by: Baig, Maugal Ahmed Ali, et al.
Published: (2012)

Design of IIUM aircraft fuselage using composite material
by: Aminanda, Yulfian, et al.
Published: (2011)

Experimental study of the strength of sandwich structure with honeycomb core
by: Aminanda, Yulfian, et al.
Published: (2011)

Autonomous control of tilt tri-rotor unmanned aerial vehicle
by: Olanrewaju, Rashidah Funke, et al.
Published: (2016)

Effect of area ratio on base pressure in a suddenly expanded duct for under expanded flow ft mach 1.87
by: Baig, Maugal Ahmed Ali, et al.
Published: (2012)

Control of nozzle flow in a suddenly expanded duct with micro jets
by: Baig, Maugal Ahmed Ali, et al.
Published: (2012)

Effect of mach number in a suddenly expanded flow for area ratio 4.84
by: Baig, Maugal Ahmed Ali, et al.
Published: (2012)

Experimental investigation of the base flow from the nozzles with sudden expansion
by: Chaudhary, Zakir Ilahi, et al.
Published: (2015)

Aeroelastic passive control optimization of supersonic composite wing with external stores
by: Sulaeman, Erwin, et al.
Published: (2016)

A matlab based educational software for the study on the effect of cut-out in aircraft wings
by: Mohammed Riyadh, Miah, et al.
Published: (2018)

Fluid-structure interactions of variable span wings in low Reynold flows
by: Salleh, Hafiz, et al.
Published: (2018)

A Model Predictive Control (MPC) approach on unit quaternion orientation based quadrotor for trajectory tracking
by: Maidul, Isla, et al.
Published: (2019)

Effects of micro jets on the flow field of the duct with sudden expansion
by: Akhtar, Mohammad Nishat, et al.
Published: (2019)

Effects of bio-inspired surface roughness on a swept back tapered NACA 4412 wing
by: Malik, Khurshid, et al.
Published: (2019)

Study of feasibility of pulse detonation engine powered by alternative fuels
by: Warimani, Mohammad Salman, et al.
Published: (2019)

Cannot write session to /tmp/vufind_sessions/sess_tjnij60c2bgt5ukpvpn2urchcd