High speed end milling in mould and die making

High speed end milling in mould and die making

Bibliographic Details
Main Authors:	Suprianto, Mohamad Yuhan, Adesta, Erry Yulian Triblas
Format:	Book Chapter
Language:	English
Published:	IIUM Press 2011
Subjects:	TA Engineering (General). Civil engineering (General)
Online Access:	http://irep.iium.edu.my/17761/ http://irep.iium.edu.my/17761/1/2.pdf

Similar Items

Influence of backcutting phenomena to surface roughness of hardened AISI H13 during high speed end milling process
by: Mohd Ali, Afifah, et al.
Published: (2011)

Predicting surface roughness with respect to process parameters using Regression Analysis Models in end milling
by: Adesta, Erry Yulian Triblas, et al.
Published: (2012)

Development of tooling cost model in high speed hard turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Development of new model for cutting force in high speed hard turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

New tool life models in turning hardened steel AISI 4340 under high cutting speed
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

Experimental investigations in high-speed hard turning of AISI 4340 steel using mixed ceramic
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Development of empirical models for surface roughness during high speed turning for hard materials using Box-Behnken design
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Influence of cutting parameters on cutting force and cutting temperature during pocketing operations
by: Hamidon, R., et al.
Published: (2016)

In-Situ syntheses of high wear resistant coating reinforced Ti-6al-4v Matrix
by: Ahmed Ghazal, Belal, et al.
Published: (2011)

Quality management system: in light of project management
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

The effect of deep cryogenic treatment on the properties of AISI D2 tool steel
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

Comparison of Polyjet Printing and Silicon Moulding as Rapid Plastic Moulding Solution
by: Singh, Rupinder
Published: (2012)

Crashing a project in PERT/CPM network
by: Syed Meera, Zahir Hussain, et al.
Published: (2011)

Coating for high speed cutting tools
by: -, Suryanto
Published: (2011)

Mould filling and pressure distribution for polymer resins
by: Mohd, Alias, et al.
Published: (2011)

Machinability study of high thermal conductivity tool steel (HTSC-150 ) in hot press die
by: Ahmad Nur Zakwan, Ahmad Nazari
Published: (2013)

High speed cutting: an approach towards improved machining performance
Published: (2011)

Investigation of minimum chip thickness in micro end milling of PMMA: process development
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Investigations of the causes of chatter in computer aided manufacturing process during end milling operation
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2011)

Investigation of chatter arising during end milling operation on VMC and quality of machined surface
by: Nurul Amin, A.K.M, et al.
Published: (2011)

Response surface methodological approach for the prediction of tangential cutting forces in end milling of stainless steel
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2008)

Investigation of Flow Behavior in Minimum Quantity Lubrication Nozzle for End Milling Processes
by: Najiha, M. S., et al.
Published: (2012)

Investigation of minimum chip thickness in micro end milling of PMMA: Experiment and analysis 800 µm diameter tool
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Efficiency of speed hump in reducing speed hump in reducing speed within higher educational institution area
by: Nur Munirah, Anuar
Published: (2018)

Investigation of minimum chip thickness in micro end milling of PMMA: experiment and analysis 1.0 mm diameter tool
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

High speed milling of mould steel using 1.5mm-diameter end-mills
by: Mohamed , Konneh, et al.
Published: (2011)

An Overview of Laser Surface Modification of Die Steels
by: S. N., Aqida
Published: (2008)

Design and fabricate blanking die fir tensile test specimen
by: Wan Mohd Firdaus, Wan Sembak
Published: (2008)

Chatter control in induction heat assisted end milling: to improve machinability of stainless steel and medium carbon steels
by: Amin, A. K. M. Nurul, et al.
Published: (2013)

Thermal simulation of laser surface processing for hot forming die surface hardening
by: Hanna, Mustafa
Published: (2013)

Modelling and analysing the cutting forces in high speed hard end milling using neural network
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2015)

Vehicle tracking and speed estimation system
by: Chan, Chia Yik
Published: (2012)

Damage detection based on the natural frequency shifting of a clamped rectangular plate model
by: Hilmy, Irfan, et al.
Published: (2015)

The development of cost structuring of high speed hard turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2009)

Content comparative investigation on tool wear during end milling of AISI H13 steel with different tool path strategies
by: Adesta, Erry Yulian Triblas, et al.
Published: (2017)

Speed studies on Malaysia East Coast expressway
by: Wahyu Nur Susianna, Omar
Published: (2017)

Finite element simulation of equal channel angular pressing: effect of die angle and number of passes
by: Dayangku Noorfazidah, Awang Sh'ri, et al.
Published: (2019)

A numerical evaluation on multi-interfaced fast handoff scheme: impact of rising link switching delay for a high speed car
by: Islam, Shayla, et al.
Published: (2016)

Determination of target speed from the FMCW radar data
by: Sediono, Wahju, et al.
Published: (2011)

Estimation and validation of wind speed by using spatial interpolation
by: Yap, Yee Von
Published: (2015)