Selection of materials and design specification for hip oint prosthesis

Selection of materials and design specification for hip oint prosthesis

Bibliographic Details
Main Authors:	Sopyan, Iis, Haruman, Esa, Sutjipto, Agus Geter Edy, Muhida, Riza
Format:	Book Chapter
Language:	English
Published:	IIUM Press 2011
Subjects:	TA Engineering (General). Civil engineering (General)
Online Access:	http://irep.iium.edu.my/17718/ http://irep.iium.edu.my/17718/1/Chapter_44.pdf

Similar Items

The use of scanning electron microscope in evaluating insulation property
by: Sutjipto, Agus Geter Edy, et al.
Published: (2011)

A maximum power point tracking for Photovoltaic system using temperature compensator method
by: Muhida, Riza, et al.
Published: (2011)

The possibility of utilizing scanning electron microscope for materials characterization
by: Sutjipto, Agus Geter Edy
Published: (2011)

Green nanotechnology using SEM and AFM
by: Sutjipto, Agus Geter Edy, et al.
Published: (2011)

Green technology of energy-efficient materials up to 70% for plasma display panel
by: Sutjipto, Agus Geter Edy, et al.
Published: (2010)

Surface breakdown property of SiO2 added MgO under electron bombardment in vacuum: a promising materials for spacecraft and space station
by: Sutjipto, Agus Geter Edy
Published: (2007)

Discharge, microstructural and mechanical properties of ZrO2 addition on MgO for plasma display panel materials
by: Bakri, Jufriadi, et al.
Published: (2009)

Novel nuclear technology for controlled production of n-type semiconductor
by: Sutjipto, Agus Geter Edy, et al.
Published: (2010)

Development of total hip joint replacement prostheses made by local material : an introduction
by: Tresna Priyana, Soemardi, et al.
Published: (2019)

Pin type reconfigurable clamping ability evaluation for setup-free technology
by: Afzeri, Afzeri, et al.
Published: (2011)

The effect of CaO addition on the microstructural, mechanical and dielectric properties of pure MgO ceramic
by: Sutjipto, Agus Geter Edy
Published: (2007)

A real-time gait event detection for lower limb prosthesis control and evaluation
by: Maqbool, Hafiz Farhan, et al.
Published: (2017)

Remote operation of CNC milling through virtual simulation and remote dekstop interface
by: , Afzeri, et al.
Published: (2009)

Neutron transmutation doped of silicon under Cf-252 isotopic neutron bombardment
by: Yahya, Roslan, et al.
Published: (2009)

Relationship between average slope of textured substrate and poly-Si thin film solar cells performance
by: Muhida, Riza, et al.
Published: (2009)

Microstructure and electrical properties of AZO films prepared by RF magnetron sputtering
by: Bakri, Jufriadi, et al.
Published: (2011)

Thermal analysis on hydroxyapatite synthesis through mechanochemical method
by: Iis, Sopyan
Published: (2011)

Material selection method in design of automotive brake disc
by: Maleque, Md. Abdul, et al.
Published: (2010)

Electrical conductivities of poly-si thin film solar cells deposited on textured substrate
by: Muhida, R., et al.
Published: (2014)

The Investigation of Mechanical Properties on Natural Fiber Composites for Recurve Bow Material Selection
by: F. A., Fauzi, et al.
Published: (2015)

Development of inert ceramic for industrial application based on ternary phase diagram of potassiun oxide-aluminum oxide-silicon dioxide
by: Sutjipto, Agus Geter Edy, et al.
Published: (2019)

Materials for bicycle frame system - a case study on the development of selection method
by: Maleque, Md. Abdul, et al.
Published: (2010)

Microstructure and mechanical properties of neutron transmutation doped silicon under Cf-252 Neutron Bombardment
by: Sutjipto, Agus Geter Edy, et al.
Published: (2011)

Introduction to probability safety assessment of nuclear power plant
by: Sutjipto, Agus Geter Edy, et al.
Published: (2011)

Thin film of indium tin oxide and its deposition technology deposition
by: Sutjipto, Agus Geter Edy, et al.
Published: (2011)

The use of SEM to investigate the effect of an electron beam on the optically-visible flashover treeing of MgO ceramic
by: Sutjipto, Agus Geter Edy, et al.
Published: (2007)

Casting investigation of heat treated biocompatible materials for total hip bone replacement
by: Mohamad Badari, Siti Norbahiyah, et al.
Published: (2011)

The development of an optimum material selection process for the design of automative brake rotor
by: Maleque, Md. Abdul, et al.
Published: (2010)

Effect of dispersant on protein foaming-consolidation porous alumina containing hydrothermal derived hydroxyapatite nanopowder
by: Sopyan, Iis, et al.
Published: (2011)

Effect of yolk addition on protein foaming-consolidation porous alumina-calcium phosphate composite
by: Sopyan, Iis, et al.
Published: (2011)

The influence of hydroxyapatite loading on protein foaming-consolidation porous alumina sintered at 1300°C
by: ., Ahmad Fadli, et al.
Published: (2011)

A simulation method to find the optimal design of photovoltaic home system in Malaysia, case study: a building integrated photovoltaic in Putra Jaya
by: Muhida, Riza, et al.
Published: (2009)

Bone implant materials from eegshell waste
by: Sopyan, Iis
Published: (2015)

Materials selection and design
by: Maleque, Md. Abdul, et al.
Published: (2013)

Research of material dispersion in optical materials for optical waveguides
by: Abdul Nasir, Abd Ghafar
Published: (2013)

Structural and wear and characteristic of low temperature nitrided stainless steel
by: Haruman, E., et al.
Published: (2006)

Improvement of typical hip-joint design for gripping and fixing
by: Mohamad Badari, Siti Norbahiyah, et al.
Published: (2011)

Design and development of interactive fish robot
by: Rahman, Md. Mozasser, et al.
Published: (2011)

An approach to enhance aggregated source specific multicast scheme
by: Hassan Abdalla Hashim, Aisha, et al.
Published: (2008)

The survivors of low class contractor in construction industry related government contract with specific at Kelantan
by: Abd Rahim, Ibrahim
Published: (2012)