Trimming of atomic force microscope probe tip by ion milling

Trimming of atomic force microscope probe tip by ion milling

Bibliographic Details
Main Authors:	Ali, Mohammad Yeakub, Lim, B.H.
Format:	Book Chapter
Language:	English
Published:	IIUM Press 2011
Subjects:	TA Engineering (General). Civil engineering (General)
Online Access:	http://irep.iium.edu.my/17714/ http://irep.iium.edu.my/17714/1/Chapter_43.pdf

Similar Items

Characterisation of surface texture using AFM with trimmed probe tip
by: Ali, Mohammad Yeakub, et al.
Published: (2006)

The study on the aspect ratio of Atomic Force Microscope (AFM) measurements for Triangular Silicon Nanowire
by: Za'bah, Nor Farahidah, et al.
Published: (2013)

Microscopic Simulation & Microscopic Analytical Model Comparison in Analyzing a Signalized Intersection
by: Azlina, Ismail, et al.
Published: (2011)

Diagonal control design for atomic force microscope piezoelectric tube nanopositioners
by: Bhikkaji, Bharath, et al.
Published: (2013)

Piezoelectric tube scanner in atomic force microscope
by: Mahmood, Iskandar Al-Thani
Published: (2011)

The use of scanning electron microscope in evaluating insulation property
by: Sutjipto, Agus Geter Edy, et al.
Published: (2011)

Spiral scanning: an alternative to conventional raster scanning in high-speed Scanning Probe Microscopes
by: Mahmood, Iskandar Al-Thani, et al.
Published: (2010)

Investigation of finish cut of microelectrodischarge milling for nanosurface finish
by: Ali, Mohammad Yeakub, et al.
Published: (2009)

Investigation of minimum chip thickness in micro end milling of PMMA: process development
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Response surface methodological approach for the prediction of tangential cutting forces in end milling of stainless steel
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2008)

Making a commercial atomic force microscope more accurate and faster using positive position feedback control
by: Mahmood, Iskandar Al-Thani, et al.
Published: (2009)

Modeling Ion propulsion plume interactions with spacecraft in formation flight
by: Kafafy, Raed, et al.
Published: (2010)

The application of scanning electron microscope and melt flow index for orange peel in laser sintering process
by: Wan Yusoff, Wan Ahmad Yusmawiza
Published: (2017)

The effectiveness of palm oil fuel ash (POFA) to resist chloride ion in concrete
by: Mohd Zhafir, Mohd Jais
Published: (2013)

Preparation and characterization of poly (amidoxime) chelating resin for metal ions removal from water
by: Siva Kumar, Supayah
Published: (2012)

Biosorption of Chromium (VI) Ions using Sustainable Eggshell Impregnated Pandanus amaryllifolius Roxb. Adsorbent
by: Noor Yahida, Yahya, et al.
Published: (2019)

Investigation of minimum chip thickness in micro end milling of PMMA: Experiment and analysis 800 µm diameter tool
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Investigation of minimum chip thickness in micro end milling of PMMA: experiment and analysis 1.0 mm diameter tool
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Characteristics of Struvite Precipitate from Palm Oil Mill Effluent
by: Mohd Yuhyi, Mohd Tadza, et al.
Published: (2015)

Modeling of milling process to predict surface roughness using artificial intelligent method
by: Mohammad Rizal, Abdul Lani
Published: (2009)

A Study of Morphological and Thermal Properties of Polylactic Acid (PLA) Modified MMT (Ion Exchange Method) Nanocomposite
by: Wan Siti Noorhashimah, Wan Kamaruzaman
Published: (2013)

Effect of milling time on mechanochemically synthesized nanohydroxyapatite bioceramics
by: Sopyan, Iis, et al.
Published: (2011)

High speed end milling in mould and die making
by: Suprianto, Mohamad Yuhan, et al.
Published: (2011)

Treatment of palm oil mill effluent by electrocoagulation process
by: Mohd Nasrullah, Zulkifli
Published: (2017)

Roles of calcium in geopolymer containing paper mill sludge ash
by: Norbaizurah, Rahman, et al.
Published: (2018)

Optimization of surface roughness in milling using neural network (NN)
by: Ruzaimi, Zainon
Published: (2010)

Optimization of surface texture in milling using response surface methodology
by: Syahrizad, Muhamad
Published: (2010)

Time domain analyis of acoustic emissions signal for milling process
by: Wan Shalamyza , Wan Husin
Published: (2012)

Slippage Detection for Grasping Force Control of Robotic Hand Using Force Sensing Resistors
by: Farag, Mohannad, et al.
Published: (2019)

Evaluation of sludge from coagulation of palm oil mill effluent with chitosan based coagulant
by: Mohd Yuhyi, Mohd Tadza, et al.
Published: (2016)

Evaluation of Sludge from Coagulation of Palm Oil Mill Effluent with Chitosan Based Coagulant
by: Mohd Yuhyi, Mohd Tadza, et al.
Published: (2016)

Milling time influence of ultrafine treated rice husk ash to pozzolanic reactivity in portlandite
by: Nuruddin, Muhd Fadhil, et al.
Published: (2016)

Influence of cutting parameters on cutting force and cutting temperature during pocketing operations
by: Hamidon, R., et al.
Published: (2016)

Bioenergy from anaerobic degradation of lipids in palm oil mill effluent
by: Anwar, Ahmad, et al.
Published: (2011)

Optimization of surface roughness in milling by using response surface method (RSM)
by: Mohd Aizuddin, Mat Alwi
Published: (2010)

Monitoring catastrophic failure event in milling process using acoustic emission
by: Haslan, Mohd Yong
Published: (2010)

Surface roughness optimization of face milling operation using Taguchi design method
by: Mohd Azmi, Md Juni
Published: (2008)

Time â�� frequency domain analysis of acoustic emission sginal for milling process
by: Mohd Shafawi, Che Ibrahim
Published: (2012)

Design and Development of Ion Probe Testing on Four Stroke Engine Model
by: Ng, Noveen Nico Alexandra, et al.
Published: (2016)

Batch study on the removal of mercury (II) ion from industrial wastewater using activated palm oil fuel ash
by: Kamaliah, Abdul Samad, et al.
Published: (2019)

Cannot write session to /tmp/vufind_sessions/sess_j89kpcbc23ccted5itfcqecfb5